The rotating shaft shown in the figure is machined from AISI 1020 CD steel. 6 kN. Find the minimum factor of safety for It is subjected to a force of F fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding.

The rotating shaft shown in the figure is machined from AISI 1020 CD steel. 6 kN. Find the minimum factor of safety for It is subjected to a force of F fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4/ Answer one of A) A cylindrical rod of 16 mm diameter is made of plain carbon steel. It is subjected to axial load of 5000 N, a steady torque of 50 N-m and bending moment of 75 N-m. Using the theories of failure to calculate:- 1) The factor of safety available. Assume yield strength as 400 MPa for plain carbon steel. And then comment on the result you get. 2) The maximum yield strength of shaft material would be necessary using factor of safety of 1.686.
42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
The rotating shaft in the given figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 6 kN. Find the minimum factor of safety for fatigue based on infinite life. Be sure to check for yielding. 500 F -175- 25 D. 35 D. 3 R. -50 D. 25 D. Dimensions in millimeters -20 -20 280- -20 20 -180 Determine the endurance limit for this material as well as the value after correction for surface finish, sizing, and loading. The endurance limit for this material is MPa. The endurance limit after correction is MPa.
In the figure, a steel shaft with ball bearings at points A and D, with cross-section narrowing at points C and D, a single load of 2 kN from B point not to rotate with the shaft, 0.1 kN/mm between points D and E so that it does not rotate together with the shaft. A distributed load of ' is applied. The shaft surface is ground and the shaft operates at room temperature with 50% reliability. Calculate the fatigue life of the shaft, taking into account the cross section narrowing point where the maximum moment occurs. All radii on the shaft are R2 mm.(Sut=690 MPa,f=0.9)
PROBLEM:1 A gas engine valve spring is to have a mean diameter of 55 mm. The maximum load it will have to sustain is 584 N with a corresponding deflection of 7.18 mm. The spring is to be made of tempered wire. Since the material is to be subjected to repeated loading and fatigue must be considered a low working stress of 650 N/mm? will be used. Find the size for wire and number of coils used. Take modulus of rigidity as 0.84 x 105 N/mm? .Assume the spring coil is squared and ground. Take shear stress Concentration factor as 1.15.
The solid steel rotating shaft in the figure is supported at B and C, and is driven by a gear, not seen, which is linked to spur gear D which has a pitch diameter of 150 mm. The drive gear force F acts at a pressure angle of 20 degrees. The shaft transmits a torque to point A of Ta-350 N.m. The properties of machined steel shaft are Sy-420 MPa and Sut-560MPa. Use a safety factor of 2.5 and determine the minimum allowable diameter in section B and C. Assume sharp felt radii at the bearing shoulders to estimate the stress concentration factors.Explain.
Dont ask for Material property. This is the only data provided. Dont keep asking for material property.
B) A simply supported shaft is shown in the following Figure. A constant magnitude distributed unit load p is applied as the shaft rotates. The shaft is also subject to a steady torque of Tmax 2000-N -m., find the diameter of shaft required to obtain a safety factor of 2.5 in fatigue loading if the shaft is steel of Sut 814 MPa and Sy 703 MPa. The dimensions are in cm, the distributed force in N/cm, and the torque is in N-m. No stress concentrations are present, the shaft is machined, the required reliability is 90%, and the shaft operates at room temperature Figure: 1= 20-cm: b = 18-cm ; a = 16 cm Applied distributed load p:= 1000 N em ; 区区

Please Explain How you Get Kt? What's d=40 there? Sut=800MPa by machining method in the figure, Shaft variable M made of a steel with Sy3640MPa subjected to moments. 50% confidence status n=2 safety according to Goodman fatigue damage criterion for the maximum moment M to be applied to the shaft. find it. 5-mm rad. 4M 4M 60 mm 50 mm M M
A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4
NO CURSIVE
Find the diameter of a shaft made of (37 Mn 2 steel) having the ultimate tensile strength as (600 MPa) and yield stress as (440 MPa). The shaft is subjected to completely reversed axial load of (200 kN). Neglect stress concentration factor and assume surface finish factor as (0.8). The factor of safety may be taken as (1.5). (After the diameter was found, correct it for the actual size factor). mechanical design pls solve fast