The rope AB exerts a 85 Newton force T on collar A. Determine the magnitude of vector component of T parallel to the bar CD. Express answer in 3 decimals and in Newtons 0.15 m -0.4 m 0.2 m 0.3 m A 05 m 0.25 m -0.2m

Q: 4- Aircraft structure is affected by some factors which cause typical damages.. Please correlate…

A: The typical damages in Aircraft structures  are due to fatigue, corrosion, wear and tear in the…

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: :The form milling from the following is

A: Option b is correct.

Q: (degree) Calculate the measure of the angle in degrees marked in white for the following figure 24…

A:

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: - Compute A.P.F. for F.C.C.?

A: APF is just the volume of the atoms within the unit cell, divided by the total volume of the unit…

Q: what is the MMC of shaft dimension 1.375 /- .030?

A: Given: The dimension of shaft  is 1375/-0.30 MMC :MMC stand for  Maximum Material Condition.

Q: A drill used in the manufacture of engine parts is designed to have seven speeds. The range of hole…

A:

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: Find the value of x5 in 3 decimal places (positive value) using Secant Method (5th Iteration) f (x)…

A: Write the given equation. fx=sinx-x take x0=0, then  f0=sin0-0=0 take x1=1, then f1=sin1-1=-0.1585

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: Convert the decimal number 11510 into its octal number equivalent

A: Convert Decimal to Octal with Steps Write the given decimal number. If the given decimal number is…

Q: Draw velocity polygon.

A: Solution:

Q: 4. How many datums are shown on the print? 5. What three symbols are used to describe the small…

A: What there's symbols are used to describe the small hole

Q: 9" 800 lb C В 4'- A 3'

A:

Q: Please show calculations

A: MMC: MMC is also called the maximum material condition. It is represented by the circled M. The…

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: . Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).

A: Givenoctal number =23228

Q: 20.00 40.00 60.00 FRONT 60.00 00'0 20.00 00'0

A: If straight lines are drawn from various points on the contour of an object to meet a plane, the…

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.