The roof system of an office building consists of a 4-in thick reinforced slab resting on four steel beams (A= 16.2 in2), in which supported by two steel girders (A=42.9 in2). The girders, in turn, are supported by four columns, as shown below. Determine the dead loads acting on the girder AG. -20 ft B Steel Steel girder (A = 42.9 in.?) column -4 in. C D concrete slab 3 at 9 ft = 27 ft E F Steel floor beam (A = 16.2 in.2) G

The roof system of an office building consists of a 4-in thick reinforced slab resting on four steel beams (A= 16.2 in2), in which supported by two steel girders (A=42.9 in2). The girders, in turn, are supported by four columns, as shown below. Determine the dead loads acting on the girder AG. -20 ft B Steel Steel girder (A = 42.9 in.?) column -4 in. C D concrete slab 3 at 9 ft = 27 ft E F Steel floor beam (A = 16.2 in.2) G

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
100% SURE PLEASE
Sub- Roof Truss (Civil Engineering)- Question 9. Double pitched roof trusses have a span of 20m and rise 2.5m. These are placed at 8m spacing between each of them. Find the maximum live load reaction at the supports.
Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultimate strength f'c = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t = 16 mm lx = 266x106 mm4 ly = 45 x 106 mm4 fy = 248 MPal Wb = 90 kg/m fy = 248MPa If each beam is laterally braced by the concrete slab, calculate the allowable bending strength using safety factor of 1.67. Select the correct response: 175.17 248.79 235.94 394.03
slab single /simple spanning slab spanning twoway/ double The timber structure below has a single spanning floor of grade C16 beams of weight 4.2 kN/m? and a two way spanning floor 150 mm thick of CLT flooring of density 410 kg/m3. Dimensions are as follows: Length a = 2.8 m %3D b = 4.4 m C = 4.4 m Find the reaction of the internal beam acting on the edge beam at X. Give your answer in kN to one decimal place. Do not put units in the answer box. The conversion from kg to kN is (x 9.81 / 1000)
Answer with Complete Solution
If beam BEH is hinged at the columns B, E, and H, determine its degree of indeterminacy.
the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the uniformly distributed service dead load at beam DEF in kN/m Calculate the uniformly distributed service live load at beam DEF in kN/m.
Answer only letter B with correct fbd
Need answer please ASAP ty!