the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min and a feed of 0.7 mm/rev is used. A mild steel rod having 35 mm diameter and 120 mm length is to be turned on a lathe. Determine the machining time to reduce 20 40 60 35 025

the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min and a feed of 0.7 mm/rev is used. A mild steel rod having 35 mm diameter and 120 mm length is to be turned on a lathe. Determine the machining time to reduce 20 40 60 35 025

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min, feed = 0.35 mm/rev, and depth of cut = 6.5 mm. The original work piece has 26 mm Diameter and 120 mm Length. How much power will the lathe draw in performing this operation if its mechanical efficiency = 90% and operator's efficiency = 82%? The specific energy is 3.8 J/mm³
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
14. Determine the proper RPM for a 3" piece of cold-rolled steel with a cutting speed of SFPM. Round the nearest RPM. Hint: Refer to formulas and examples in your textb а. 102 b. 115 C. 87 d. 146 15. Calculate the machining time (in minutes, rounded to the nearest minute) for a part in length 10" diameter AISI/SAE 4140 steel using a cutting speed of 110 SFPM and a rate of 0.008 IPR. Hint: Refer to examples in your textbook. а. 47 b. 60 C. 86 d. 74
To facilitate the milling (roughing) work of a cast steel material using a 1.5 inch diameter cutter choose between the two available stock. Find the speed of the cutter in rpm. – high speed steel cutter with a cutting speed of 50 fpm or – carbide tipped cutter with a cutting speed of 200 fpm.
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
b) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm, for the length of 22cm by turning on lathe, with a spindle speed of 250rpm. Assume feed (f) 2.5 mm/rev and 2 passes to complete the turning operation. Write the formula and calculate (i) Cutting speed (ii) Depth of cut.
Figure Q3 shows a vehicle uses water scooping to slow down. The scoop is 3-m wide. Draw the free body diagram of the scoop. Determine the amount of force exerted on the scoop. The vehicle is traveling at 100 km/hr and it scoops off 10 cm of water.
6
Plate 200 mm x 90 mm is to be maintained on a shaper under following condition, v= 13.5 m/ min Feed is 0.57 mm/ double stroke, Approach and overtravel 20 mm each in longitudinal direction and 4 mm each in lateral direction. The ratio of cutting to the return speed is 0.83.Calculate the machining time in minutes?
Handwritten solution recommended. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and depth of cut = 2.5 mm. The tool used in this cutting is cemented carbide tool where Taylor tool life parameters are n = 0.24 and C = 450 (tool life (min) and cutting speed (m/min). Compute the cutting speed that will allow the tool life to be 10% longer than the machining time for this part.