The rigid, horizontal slab is attached to two identical copper rods. There is a gap ∆ = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 60 oC. Use the following data

The rigid, horizontal slab is attached to two identical copper rods. There is a gap ∆ = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 60 oC. Use the following data

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.70 ox= X The state of stress at a point is given by : = 80 MPa, oy=100 MPa = and txy = 60 MPa. If the yield strength for the material is 150 MPa, as determined in a uniaxial test, then the maximum shear stress is, nearly A 75.5 MPa B с D 127.4 MPa 119.3 MPa 104.0 MPa
Please solve all part ? and correct
A high-density polyethylene [E= 104 ksi and a 74 x 10-6/°F] block (1) is positioned in a fixture. The block is 2.2 in. by 2.4 in. by 39 in. long. At room temperature, a gap of 0.08 in. exists between the block and the rigid support at B. Determine: (a) the normal stress a in block (1) caused by a temperature increase of 40°F. (b) the normal strain e in block (1) at the increased temperature. Answerrs: 0 (a) σ= (b) e 0.08in. 39 in. psi. με.
For a given steel cube section subjected to three dimensional state of principal stress. 75N/mm² ŠI 150 N/mm 30 N/mm² Consider yield stress = 250 N/mm², and µ = 0.3 The value of factor of safety according to maximum strain energy theory. -X
The state of stress at a point in a structural member may be represented by a two-dimensional stress system in which o, =100 N/mm², o,=-80 N/mm² and 7,, =45 N/mm². Determine the direct stress on a plane inclined at 60° to the positive direction of o, and also the principal stresses. Calculate also the inclination of the principal planes to the plane on which o, acts. Verify your answcrs by a graphical method. Ans. 6,= 16 N/mm², o1 =110.6 N/mm², ơn=-90.6 N/mm², 0= –13.3° and –103.3°. !!
Q- A stepped steel shaft is subjected to a clockwise torque of 10 Nm at its free end. Shear modulus of steel is 80 GPa. Find the strain energy in the shaft? A 50 mm dia 100 mm B 25 mm dia 100 mm C K T=10 Nm
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 1.9 GPa. Each bar has a cross-sectional area of 900 mm2. Using L = 395 mm and Δ = 4.6 mm, what magnitude of load P will cause the normal stress in each bar to be the same value?
A 3-m long aluminum bar with a cross-sectional area of 320 mm2 is placed between two rigid walls as shown below. The gap A on the right end of the bar is 3 mm. Determine the stress in the bar when the temperature rises 45 Co. Use a = 23 um/(m-Co) and E = 70 GPa. L = 3 m
For the structure shown below, calculate the following things: a. Normal stress in wire AB when P = 10 kips %3D b. change in diameter in wire AB when P = 10 kips c. Normal stress in wire BC when P = 10 kips d. Normal stress in wire CE when P = 10 kips e. Normal stress in rigid beam CD when P = 10 kips f. allowable applied load (P, allowable) if yield stress in wire is 60 ksi and F.S. = 2. Note: All wires have diameter of 1 inch, E = 10000 ksi, and v (poisson's ratio) = 0.3 Also, area of rigid beam CD is 4 in^2. A B 45 Deg. 60 deg. 60 deg.
2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in Fig. 2-42. Through a fabrication error, the central bar, ②2, is 0.0005L too short. All bars are of identical cross section and of steel having E = 210 GPa. Find the stress in each bar after the system has mechanically been pulled together so that the gap A is closed. Ans σ-35 MPa σ = 70 MPa Fig. 2-42
Choose the correct one and explain it
a)Calculate the stress in the copper bar (in MPa).b)Calculate the axial deformation in the brass bar (in mm).c)Calculate the axial deformation in the brass bar (in mm).