The results of a consolidated undrained test, in which o3 = 392 kN/m², on a normally consolidated clay are given as: Axial strain (%) Ao(kN/m²) ug(kN/m²) 0.5 0.75 156 196 226 235 250 245 240 235 99 120 132 147 161 170 173 175 1.3 3 4 4.5 Draw the K; line in a P' versus q' diagram. Also draw the s tress path for this test in the diagram.

The results of a consolidated undrained test, in which o3 = 392 kN/m², on a normally consolidated clay are given as: Axial strain (%) Ao(kN/m²) ug(kN/m²) 0.5 0.75 156 196 226 235 250 245 240 235 99 120 132 147 161 170 173 175 1.3 3 4 4.5 Draw the K; line in a P' versus q' diagram. Also draw the s tress path for this test in the diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the stressed soil element shown:a. Compute the major principal stressb. Compute the minor principal stressc. Compute the normal stress on plane DE
5. [Shear Strength] ( e). In a series of unconsolidated-undrained triaxial tests on speciments of a fully saturdated clay, the following results were obtained at failure. Minor Principal Stress (КРа) 200 400 600 Major Principal Stress 422 618 820 Calculate the following: a. Cohesion b. Angle of internal friction
A consolidated-drained tri-axial test was conducted on a normally consolidated clay. The results are as follows: O3 = 150 kN/m? (Aoa)f= 130 kN/m? Determine a. Angle of friction, o' b. Angle 0 that the failure plane makes with the major principal plane c. Find the normal stress o' and the shear stress tf on the failure plane d. Determine the effective normal stress on the plane of maximum shear stress
5. A consolidated, undrained triaxial test is being carried out on a normally consolidated clay where c - 0 and p'= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
A clay specimen with drained shear strength parameters of c'=5 kPa and Φ=320 is consolidated under all around pressure of 140 kPa.The specimen was then loaded axially to failure under undrained condition and failed when the principal stress diffrences reached 60 kPa.Calculate the pore pressure(u) and the pore pressure coefficient D(=A*B=Δu/Δσv) of the clay.
2- A three-axis compression test on a clay sample that is comprehensive and normal up to a stress of 300 kPa and a specific volume of 2 Consolidated is done, The values of q and volumetric strain are measured at axial strain, 0, 2 and 10 percent (failure) . The value of N is equal to 3 and A is equal to 0.2. Graph of all-round stress on initial all-round stress Draw the initial all-round stress in terms of section
7.12 A sand specimen was subjected to a drained shear test using hollow cylin- der test equipment. Failure was caused by increasing the inside pressure while keeping the outside pressure constant. At failure, o, = 193 kN/m² and o; = 264 kN/m². The inside and outside radii of the specimen were 40 and 60 mm, respectively. (a) Calculate the soil friction angle. (b) Calculate the axial stress on the specimen at failure.
A consolidated-undrained test determines that the shear strength of a normally consolidated clay is given by τf = σ’tan 27o. The confining pressure is 150 kPa, and deviator stress at failure is 120 kPa.• Find the consolidated-undrained friction angle• Pore water pressure developed in the specimen at failureFinal answer should be in 3 decimal places.
Q: A consolidated-drained tri-axial test was conducted on a normally consolidated clay. The results are as following: confining stress, G3 = 150 kN/m² and deviator stress, (Aod)t = 150 kN/m². i) Determine angle of friction, q; ii) Determine angle 0 that the failure plane makes with the major principal plane; iii) Find the normal stress and the shear stress ty on the failure plane; and iv) Determine the effective normal stress on the plane of maximum shear stress. Express your results in two decimal places.
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
A sample of sand is sheared in the following manner. First an all around normal stresso 350 kPa is applied to the sample. Next a shear stress is applied to the horizontal pia while the normal stress remains constant. The shear stresses at failure are + 186 kPa. Ihe initial stress and stress condition at failure are shown below 350 kPa 350 kPa 186 kPa 350 kPa 350 kPa ー550 kPa 550 kPa 186 kPa 350 kPa 350 kPa Initial Conditions At Failure Determine the Following: fo A) Assuming c, = 0, draw a failure envelope for the soil. Define the friction angle ( the soil. B) Draw the Mohr's Circle at failure for the test. C) Show the location of the pole. D) Define the maximum and minimum principal stresses at failure. E) Define the normal stress corresponding to the maximum shear stress
A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.