The resultant of the forces P1, P2, and the couple C is the force R= 35.6k N acting at a point A (R is not shown in the figure). Determine P1, P2 and C

Q: In the plane forces system, F, = 6 kN, F2 = 4 kN and F3 = 5 kN. The direction of the force F3 is tan…

A: To find: Resultant force, R = ? kN Line of action = ?

Q: - Determine the resultant of forces system shown in Figure with its direction and locate it with…

A: Find the resultant force and its direction and location from point C.

Q: The weight of the plate is 300-N.. The tension in cable AB is 350-N, and tension in cable CD is…

A: Given data, Weight of the plate, W = 300 N Tension in cable AB, TAB = 350 N Tension in cable CD, TCD…

Q: Determine the magnitude of the resultant R for the F1 and F2 combination. b) Where should the…

A:

Q: Determine an equivalent system at C for the force they act on the structure

A: given:

Q: F=300N im P: 400 N

A:

Q: The moment of the force F=720-lb about the point O in Cartesian vector form is. F 1 ft 4 ft 2ft 4…

A: Solution: Moment of Force F about O and its cartesian form is obtained below.

Q: Three coplanar forces are given as follows: A=6 N at 250°, B= 10 N at 120°, and C = 16 N at 205°…

A:

Q: Q2. In Figure Q2, ropes AB and AC are tied at point A which is 5 m from the base of the tree, O. The…

A:

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A: To calculate the resultant, we need to first resolve the forces in vertical and horizontal…

Q: Given the Position vector R= -i+ 6j + 3k (m) and the Force vector F = -i - 3j + 8k (kN)

A: Given, the Position vector. R⇀=-i+6j+3k m Force vector, F⇀=-i-3j+8k kN   The dot or scalar product…

Q: 30UN beam. The resultant couple is zero. 0.2 m 500 N Find: The magnitudes of the forces P and F and…

A:

Q: Q4) If the two forces fi= 6N and F2= 4 N and the angle between them 0 =60 , the resultant of them R…

A:

Q: The moment of the force F-120-lb about the point O in Cartesian vector form is.

A:

Q: Problem 1: From the figure, F1 =22KN, F2 =27KN 1. Find the resultant of the forces 2. Find the…

A: Consider the diagram as shown below for the given system.

Q: Replace the forces system in the figure with an equivalent force at A and a couple moment so their…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A:

Q: The line of action of the 3110-lb force runs through the points A and B as shown in the figure.…

A:

Q: For the block shown in the figure below, the 50 Ib. force is passing through points JI, the 30 Ib.…

A: Given data   Coordinates of the points in the boxO (0,0,0)B(0,4,4)C(0,8,4)E(0,8,0)I(6,8,0)Position…

Q: Find the magnitude and direction of the resultant for system of forces shown in the figure. Take F1=…

A:

Q: of the transmission tower. The tension force in cable AC is 8 kN. Determine the required tension…

A: Given data Tension force in cable AC = 8KN

Q: Q1: Determine the moments from two forces of P and Q about point O. Please solve using vector and…

A: Step 1:Step 2:Step 3:please give helpful rating  Step 4:

Q: Q3. Find the resultant of the forces act on a wall as shown in the figure below: F = 800N 45°…

A: Given:

Q: Q2/ Determine the resultant of forces system shown in Figure and locate it with respect to point C?…

A:

Q: 1. A 5kN force is applied to the pulley system as shown. The member OA is a simple two force member.…

A:

Q: Find the resultant of the forces F1, F2, and F3? F2=100 N F3=100 N 450 F1=100N

A:

Q: Given a system made of the force F, couple M and distributed loads defined by w1 and w2, find the…

A: To find :  The equivalent system at B  Given :  The Force is F=8 kN The moment is M=5 kN·m The…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.