The readings of the two instrument connected to a balanced three-phase load are 128 W and 56 W. When a resistor of about 25 ohms is added to each phase, the reading of the second instrument is reduced to zero. The power in the circuit before the resistors were added?

Q: If Current and Voltage are 90 Degree Out of Phase in a single-phase circuit, then the true power…

A: If voltage and current are in 90 degree out of phase  Power factor = cos(phase angle) = cos(90) = 0…

Q: A wye connection load has a voltage of 480v applied to it. What is the voltage dropped across each…

A:

Q: What would be the same results of this quesiton if the circuit was single phase 1000v?

A: If True power is single phase i.e.,P1ϕ=10kWV1ϕ=1000VI1ϕ=12.33 A

Q: The DC resistance of a delta connected alternator measured across its two terminals is 1 ohm. What…

A: Draw the given arrangement of delta connection for measurement of resistance and using given DC…

Q: Question No.84 Three loads, each of resistance 50 Q are connected in delta to a 400 V, 3-phase…

A:

Q: a wye connected load as 480v applied to it what is the volatage drop across each phase?

A:

Q: A resistor of 50 ohms and an impedance of 100 + j50 ohms are connected in parallel across a 220…

A:

Q: A 50-ohm, a 90-ohm and an unknown value resistor are in series across a 60-V generator with 1/3A…

A:

Q: 2. An inductive reactance of 8 N is connected in parallel with a capacitive reactance of 18 N; this…

A:

Q: Question: For the basic chopper circuit Edc= 50 V, R= 80 ohms, duty cycle is 30% then the average…

A:

Q: 17 In the figure shown, the voltage V1 the voltage V2 by. ||||||| out of phase. *

A: The Voltage waveform when represented on a same plot can be compared easily because they become…

Q: Explain briefly why is there no wattmeter reading when the load is purely capacitive.

A:

Q: Problem 5 For two electrical system shown in Figure 5, use cyclic currents to derive a complete…

A: Since you have asked multiple questions so we will solve part (a) question for you. If you want any…

Q: A 50-ohm, a 90-ohm and an unknown value resistor are in series across a 60-V generator with 1/3A…

A: given circuit

Q: A single phase load is located 2800 feet from its source. The Load draws a current of 86 A and…

A: A single phase load is located 2800 feet from its source. The Load draws a current of 86 A and…

Q: inductive reactance of 8 ohms i ch a capacitive reactance of 18 o then connected in series with a v…

A:

Q: What is the difference between load and delta?

A: Delta is a type of connection in which we connect the load or source on delta .

Q: 450 Q 6 Vrms 340 Q 600 2 200 Q

A:

Q: The variable AC voltage available from the power module is a (A) single-phase (B) 2-phase balance…

A: Variable ac voltage is the output of a variac transformer. To meet the load requirements various…

Q: Three identical capacitors of 25 micro farad are connected In staf acrUss 400 VUILS, 50HZ, 3-phase…

A: Here, we have three identical capacitors connected in star connection with a supply voltage of 400…

Q: In a series AC resistive circuit: O a) voltage leads current by 90°(degrees). b) current leads…

A: Option c Current and voltage are in phase

Q: 4. Considering your house domestic load and complete this assignment with approximate values of the…

A: To find total power of each load, it gets adds up.

Q: In three phase power each voltage current and power is delivered by how many degrees..

A: Phase Phase is the difference between the starting position of the two sinusoidal waveform, so it…

Q: Calculate the power factor and phase angle in a sinusoidal current-carrying circuit from measuring…

A: Given Data: Readings of, Ammeter Im= 2.5 A Voltmeter  Vm=200 V Wattmeter  Pm=220 W Full Scale…

Q: In a three phase -four wire star connected system, the three outer wires are called as lines and the…

A: Fig: Three phase four wire system In the above shown system the common wire (N) in the…

Q: 2. Convert the following current source into an equivalent voltage source and redraw the circuit.…

A:

Q: Match the following Each load will be connected between two phase wires Choose... Power measured by…

A: Given, Match the following Each load will be connected between two phase wires  Power measured by…

Q: What will happen in each of these systems to the phase voltages of the load, if one of the source…

A:

Q: 4. A resistor and inductor are connected in parallel to a 277 volt, 60 Hz line. The resis- tor has a…

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.