The reading taken on a staff held at a distance of 50 m from the instrument with the able central is 1.465. When the bubble is moved 4 divisions out of the centre, the staff reading is 1.472 m. What will be the radius of curvature (m) of the bubble tube, if the length of one division is 2 mm?

The reading taken on a staff held at a distance of 50 m from the instrument with the able central is 1.465. When the bubble is moved 4 divisions out of the centre, the staff reading is 1.472 m. What will be the radius of curvature (m) of the bubble tube, if the length of one division is 2 mm?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the deflection at the center of a simply supported beam in mm, if the beam has a length…

A: Given data- EI=4.5 m4 Pa

Q: 1.52 m 2.1m ー斗子om 2.28 m 7m

Q: For the thin-walled tube shown, the polar moment of inertia is about * .21714.6 mm^4 2 mm 12mm True…

A: Given data in question Tube Inner diameter Thickness To find out Polar moment of inertia

Q: 150 kN 50 kN/m E C D 21

Q: Help me, thank you! A 100- m steel tape is used to measure the distance of the line and found to be…

A: Surveying mainly considers the branch of measurement of the points on the ground surface for the…

Q: A Civil Engineer used a 40m tape in measuring an inclined distance. The measured length on the slope…

Q: For the structure shown in Figure, apply virtual work to calculate i) the vertical deflection at…

Q: Q3) Several forces are applied to the steel pipe assembly shown below. The pipe has inner and outer…

A: A pipe section is given below. To this load are applied as mentioned. The pipe is fixed at its base…

Q: The theodolite instrument can measure both horizontal and vertical angles with high accuracy. O a.…

A: The theodolite instrument can measure both horizontal and vertical angles with high accuracy Given…

Q: 500KN 200mm 100mm C 45° %24

Q: A line was recorded as 2500.00 meters long. The standard tape weighs 0.65 kg, 30.00m long at 20°C…

Q: For the beam in Question 2, suppose that instead of the pin support, we instead have a clam support…

Q: Movement of a radially embedded arm θ = 0.2t + 0.02t^ 3 The equation (radians, t seconds) is given.…

A: given data,θ=0.2t+0.02t3r=0.2+0.04t2ve=rω=rdθdtve=(0.2+0.04t2)d(0.2t+0.02t3)dtve=0.414m/secwhere ve…

Q: In fig. , if L= 100 cm and the angle = * ?--- =25°, h Paim 4. 0.422 cm (O 0.422 m O

Q: A civil engineer used a 30-m tape in measuring an inclined distance. The measured length of the…

Q: W = 30 K/m L= 3m E- 18GPA;b=200 mm %3D d: 400 mm

Q: beam with span of 12 m has overhanging portions at both ends and is loaded with a uniform…

A: Given Data:Overhanging beamSpan L=12mUDL= 28kN/mE=200 GpaI=1×109mm4 It is required to determine the…

Q: A simply supported beam, having a length of 9.0 m, is being subjected to a concentrated live load of…

Q: A reducing elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward 30°…

A: given data:- mass rate of flow=14kg/s inlet area=113cm2 outlet area=7cm2 head difference=30 cm

Q: Figure P9-84 represent the steel shaft of a machine. The gears mounted on the arrow produce the…

Q: Solve for the vertical deflection at A

Q: Use a steel strip with a length of 20 m and a cross-sectional area of 5 mm2 and its weight 1.5 kg…

A: .

Q: or questions 1A and 1B, consider the figure below and the given modulus lasticity E, and moment of…

A: To find slope and deflection at free end

Q: A simply-supported reinforced concrete beam, 300 mm wide x 600 mm deep spans 8 m. Its fundamental…

Q: Analyze the beam shown below by Slope - Deflection Method 10 kN/m 8 kN/m 10 kN/m A ID Bo00 4 m 4 m 4…

Q: The measurements x1 = 8m, x2 = 6m, and x3 = 4m represent the sides of a rectangular parallelepiped…

A: The values given in the question are as follows x1=8 m x2=6 m x3=4 m Systematic errors are ∆x1=0.004…

Q: What must be the pull in a (7)(10) meters tape in order to eliminate the sag and temperature…

Q: Using DIM or MAM or CBM, find the vertical displacement at the midspan of the beam shown, El is…

Q: The shape of the hydrograph is affected by different parameters. * O False True

A: The shape of hydrograph depend on : Vegetation Intensity of rainfall Topography Shape of drainage…

Q: A metal bar of length 100 mm is inserted between two rigid supports and its temperature is increased…

Q: DOUBLE INTEGRATION wA = 6 kN/m wB = 15 kN/m L = 8 m The first constant of integration, c1?…

A: Free body diagram - Force in the vertical direction - RA + RB = 6×8 + 1215-6×8⇒RA + RB =84KN…

Q: Further questions (submit on another sheet; stapled to this one) 6. 1,0 x 2,0 rectangular steel…

A: Question is based on the rectangular steel plate subjected to forces. Dimension of plate and…

Q: Determine the magnitude of the correction per tape length in meters due to sag. Round off your…

Q: A civil engineer used a 200 m tape in measuring an inclined distance. The measured length on the…

Q: Analyze the structure below using Double Integration Method. 10KN/m 5KNM A B 5m m

Concept explainers

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.

Question

The reading taken on a staff held at a
distance of 50 m from the instrument with the
able central is 1.465. When the bubble is
moved 4 divisions out of the centre, the staff
reading is 1.472 m. What will be the radius of
curvature (m) of the bubble tube, if the length
of one division is 2 mm?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given information

VIEW

Step 2: Find the radius of the curvature

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Situation #1: Find the value of the diameter at point B. d, = 150 mm V = 1.5 m/s A B d, = ? V, = 2.5 m/s
A Civil Engineer used a 50m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial point and the end point was found to be 1.25 m. The 50 m tape is of standard length at a temperature of 10°C and a pull of 50 N. During measurement the temperature reading was 16°C and the tape was supported at both ends with an applied pull of 60 N. The cross-sectional area of the tape is 6 mm2 and the modulus of elasticity is 200 GPa. The tape has a mass of 0.075 kg/m. Coefficient of thermal expansion is 0.0000116 /°C. Determine the magnitude of the correction per tape length in meters due to temperature. Round off your answers to 4 decimal places. Determine the magnitude of the correction per tape length in meters due to pull. Round off your answers to 4 decimal places. Determine the magnitude of the correction per tape length in meters due to sag. Round off your answers to 4 decimal places. What is…
choose the correct answer
The 30kg rectangular plate shown in the given figure is suspended by its center from a bar whose torsional velocity is K = 10Nm / Orad. Determine the natural period of vibration of the plate when it experiences a small a = 0.25m, angular displacement 0 from its plane. Where: b = 0.35m. Find your D.C.L
An engineer used a 30 m tape in measuring an inclined ground 459.20 m long. The difference between the starting point and end point is 1.20 m. The tape is of standard length at a temperature of 100 C and a pull of 50 N. During measurement the temperature reading was 15 0 C and a pull of 75N applied at both ends. A= 6.5mm2 ; E = 200GPa; K = 0.0000116 m/C0 . The mass of the tape is 0.075kg/m. Determine the horizontal distance.
Determine the axial forces, shears, and bending moments at points A and B of the structure shown.
Determine the deflection @Cusing Moment Area Method. (Your final answer should be in "mm") 8 kN/m 3 kN A C D 6 т 4 m 3 т E = 200 GPa I = 260 x 106 mm4 %D
2. A simple harmonic oscillator takes 10.0 s to undergo five complete vibrations. Find (a) the period of its motion, (b) the frequency in hertz, and (c) the angular frequency in radians per second.
Note please help us in this sample question we really need it so that we can understand it thank you and also please put it in 3 decimal places