The ratio of area of cross section of the two pistons in a hydraulic machine is 1:15. Find the force that should be applied on the narrower piston to overcome a force of 120 N on the bigger piston. O 20 N 8 N O 150 N O 10 N

The ratio of area of cross section of the two pistons in a hydraulic machine is 1:15. Find the force that should be applied on the narrower piston to overcome a force of 120 N on the bigger piston. O 20 N 8 N O 150 N O 10 N

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: A swimming pool has dir (a) What is the force exerted by the water on the bottom? N down (b) What is…

Q: A car of mass 1290 kg rests on a hydraulic lift with a piston of radius 0.24 m that is connected to…

A: The mass of the car is 1290 kg.The radius of the first piston is 0.24 m.The radius of the second…

Q: A hydraulic system has two pistons of different diameter and uses a liquid of density p=1260 kg/m3.…

A: pressure on side of smaller piston = F1/A1 = (1.3*9.8)/π(0.01)2 = 40552.68 Pascalspressure on side…

Q: In the figure, a spring of spring constant 2.20 x 104 N/m is between a rigid beam and the output…

Q: In the figure, a spring of spring constant 2.30 x 104 N/m is between a rigid beam and the output…

A: Given : spring constant k=2.30 × 104 N/m Area of input : Ai Area of output : 13Ai Compression…

Q: st species of clingfish (family Gobiesocidae), pelvic and pectoral fins converge to form a suction…

Q: Piston B has a diameter of 40.0cm and an output force of 200 N. What is the input force on piston A…

A: Given: The diameter of piston B is d=40 cm. The output force is F=200 N. The diameter of piston A is…

Q: (a) Calculate the work done by a 5.6 N force pushing a 400. g sandwich across a table 0.75 m wide.…

Q: The hydraulic lift (Fig. 2) is a device allowing lifting heavy objects (e.g. a car) by applying…

A: Given AoutAin=10

Q: The spring of the pressure gauge shown in the figure below has a force constant of 1 000 N/m, and…

A: The force needed to move the piston is,Substitute the values,

Q: 10 cm 10 cm Water Air E Air 10 cm D 10 cm 5 cm 5 сm A Hg Hg F FF Hg 10 cm 10 cm G For the given tank…

Q: consider an 800-g ball, tied to a 1.300 m inextensible cord, and is released from rest at position 1…

Q: A swimming pool has dimensions 36.0 m ✕ 7.0 m and a flat bottom. The pool is filled to a depth of…

A: Given, The dimension of the swimming pool 36×7, The depth of the pool, h=1.90 m

Q: Three hydraulic lift systems are shown below. Rank, from largest to smallest, the magnitudes of the…

A: Concept

Q: Although gas station owners lock their tanks at night, a gas station owner was the victim of theft…

A: The pressure of the best vacuum pump available P=192 mbar=19200 Pa. The specific gravity of gasoline…

Q: bu wash your roof with a water hose at a height of 8.0 m above the ground. You connect two garden…

Q: To what height should a cylindrical vessel be filled with a homogeneous liquid to make the force…

Q: The drawing shows a hydraulic chamber with a spring (spring constant = 1690 N/m) attached to the…

A: Given data: Spring constant (k) = 1690 N/m Mass (m) = 45.0 kg Required: The compression in the…

Q: (a) A rectangular access panel in the side of an open storage water tank is 0.2m wide x 0.2m high as…

A: “As per the policy we are allowed to answer only 1 question at a time, I am providing the same.…

Q: 500 kg 2.0 in. be–10 in. (2

A: Given: The diameter of piston-1 is 0.5 cm. The diameter of the piston-2 is 2.5 cm. The load on the…

Q: creating a vacuum as illustrated in the image. What will be the height difference between the two…

Q: A cylinder with cross-section area A floats with its long axis vertical in a liquid of density p A…

Q: A force of 500 N is applied to a hydraulic jack piston that is 0.04 m in diameter. If the piston…

A: Given data: Force on hydraulic jack (F1) = 500 N Diameter of jack piston (d1) = 0.04 m Diameter of…

Q: Although gas station owners lock their tanks at night, a gas station owner was the victim of theft…

A: Given that:Specific gravity=0.712Density of gasoline, ρ=0.712×1000=712 kg/m3

Q: The input and output pistons of a hydraulic car lift have diameters of 3.00 in and 25.0 in,…

A: Solution:-Given thatDiameter of input piston (D1)=3 inDiameter of output piston (D2)=25 inWeight of…

Q: If the speed of a fluid through a tube of radius r = 1 cm is v = 0.2 m/s, then the flow rate through…

Q: The cross-sectional area of the smaller piston of a hydraulic press is 129 cm? while the area of the…

A: area of cross section of small piston = A1= 129 cm2 area of cross section of larger piston = A2=…

Q: A mass m₁ = 70 kg is balanced by a mass m2 = 1200 kg on an oil hydraulic lift. The diameter of the…

A: This is a question from the Hydraulic lift system. We will elaborate more about the problem in the…

Q: as far an capillary action concern the Liquid of high density has curved surface. O True False оо

A: as for an capilary action concer the liquid of high density has curved surfaces. FALSE

Q: A water cannon 2.15 m long and with a cross-sectional area of 11.0 cm2 is aimed straight up and…

A: Length of water cannon = 2.15 m A1 = 11 cm2v1 = 8.8 m/s A2 = 46 cm2Using equation of continuity…

Q: A force of 295 N is applied to a hydraulic jack piston that is 0.026m in diameter. The second piston…

A: Given data: Force applied to first piston (F1) = 295 N Diameter of first piston (d1) = 0.026 m…

Q: Find the force P that must be applied to a piston of area 11.60 cm2 to produce sufficient fluid…

A: Given : piston area (A) = 11.60 cm2weight of car = 10001 N fluid cross sectional area on the side…

Q: A simple U-tube contains mercury. When 11.2 cm of water is poured into the right arm, how high does…

A: Given, Water poured at right arm h1 = 11.2 cm = 11.2 x 10-2 m

Q: Design a steel structure on which an overhead water tank is resting. Consider the height of the…

A: length L= 5m area S= 3m height H= 4m Height of the tank = 2.5m The thickness of the water tank=0.25…

Q: A force of 343 N is applied to a hydraulic jack piston that is 0.0388 m in diameter. The second…

Q: A liquid flows through two similar pipes 1 and 2. If the ratio of their flow velocities v1 : v2 is…

A: By the conservation of energy, the heat loss in the two pipes = the kinetic energy gain by the…

Q: The method of capillary rise is based on the height to which the liquid in the capillary will rise…

A: It is force due to gravity F= mg m = mass g = gravitational constant

Q: A 70.0 kg person balances a 1200 kg elephant which is standing on a 1200 kg circular lift of…

A: Consider the mass of the student is Ms=64 kg Mass of elephant is Me=1200 kg The diameter of the…

Q: Two capillary tubes with an internal diameter of 1.6 mm and 0.96 mm were inserted into a liquid of…

A: Given: Diameter of first tube R1 = 1.6 mm. Diameter of first tube R2 = 0.96 mm. Density of the…

Q: A cylindrical storage tank has a cross sectional area A1=1.5 m². The tank is set up vertically on…

Q: A hydraulic press contains oil of density po = 800 kg m, and the areas of the large and small…

Q: A force of 295 N is applied to a hydraulic jack piston that is 0.026 m in diameter. The second…

A: GivenF1 = 295 Nd1 = 0.026 md2 = 0.19 m

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

The two pipes shown in Fig 14 has contact diameter, determine the velocity, V2 and V3 of water coming out of the pipe. pwater=1000kg/m³, 1atm 105 Pa P₁ = 2 atm V₁=1.0- P₁ = 2 atm V₁ = 1.0- S 10 m = P₂= 1 atm V₂ = ? P3= 1 atm V3 = ?
A swimming pool has dimensions 34.0 m x 7.0 m and a flat bottom. The pool is filled to a depth of 1.50 m with fresh water. (a) What is the force exerted by the water on the bottom? N down (b) What is the force exerted by the water on each end? (The ends are 7.0 m.) N outward (c) What is the force exerted by the water on each side? (The sides are 34.0 m.) N outward
Question 5 1 pts F2 F3 600 1000 600 600 Consider the three hydraulic lifts shown above. Rank the forces requi on the input arm (F1, F2, F3) if you want to keep the input and output arms at the same height. The input pistons all have equal diameters. The output pistons all have equal diameters. O F2 > F1 = F3 O F3 > F2 > F1 O F3 = F2 > F1 O F2 > F3 > F1 O F1 = F2 = F3
To what height should a cylindrical vessel be filled with a homogenous liquid to make the force with which the liquid presses on the sides of the vessel equal to the force exerted by the liquid on the bottom of the vessel?
A swimming pool has dimensions 36.0 m ✕ 6.0 m and a flat bottom. The pool is filled to a depth of 2.10 m with fresh water. (a) What is the force exerted by the water on the bottom? N down(b) What is the force exerted by the water on each end? (The ends are 6.0 m.) (c) What is the force exerted by the water on each side? (The sides are 36.0 m.)
A Volkswagen with mass m = 8.00 x 102kg is at rest as shown in the figure. Both pistons have a circular cross-sectional area. The small piston has a diameter of d1 = 0.25 m and the large piston has a diameter d2 = 4.5 m. Determine the magnitude of the forceexercised on the small piston.
Three solid objects are floating in a liquid, as in the drawing. They have different weights and volumes, but have the same thickness (the dimension perpendicular to the screen). Rank the objects according to their density, largest first. O A, C, B O A, B, C O B, A, C O B, C, A O C, A, B C
In the figure, the fresh water behind a reservoir dam has depth D = 14.0 m. A horizontal pipe 3.51 cm in diameter passes through the dam at depth d= 5.62 m. A plug secures the pipe opening. (a) Find the magnitude of the frictional force between plug and pipe wall. (b) The plug is removed. What water volume exits the pipe in 2.00 h? (a) Number (b) Number Units Units
A swimming pool has dimensions 26.0 m x 11.0 m and a flat bottom. The pool is filled to a depth of 2.50 m with fresh water. (a) What is the force exerted by the water on the bottom? N down (b) What is the force exerted by the water on each end? (The ends are 11.0 m.) N outward (c) What is the force exerted by the water on each side? (The sides are 26.0 m.) N outward
A moonshiner produces ethanol and stores it in a stainless tank in the form of a cylinder, 20 cm in diameter with a tight-fitting piston at the top. The total volumetric capacity of the tank is 0.20 m3 (200L). In an attempt to squeeze a little more into the tank. he piles lead bricks on the piston, the total mass of the bricks and piston is 120 kg. What additional volume of ethanol can he squeeze into the tank? Kethanol=11 x 10-10 Pa-1.
In an industrial cooling process, water is circulated through a system. If water is pumped with a speed of 5.20 m/s under a pressure of 5.00*10^5 Pa from the first floor through a 3.80-cm diameter pipe, what will be the pressure on the next floor 3.50 m above in a pipe with a diameter of 3.00 cm?
Water rises to height of 10 cm in a certain capillary tube. If the same capillary is dipped into mercury, the level of mercury decreases to 3.42 cm. Compare the surface tension of water and mercury, if densities of mercury and water are 13.6 × 10³ kg/m³ and 10' kg / m³ respectively. Angle of contact for water is 0° and that for mercury is 135°.