Answered: The range of frequencies a channel can…

Engineering

Computer Science

The range of frequencies a channel can pass is called bandwidth in Hertz why?

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 14VE

See similar textbooks

Related questions

Q: If the channel is band limited to 6 kHz and signal to noise ratio is 16, what would be the capacity…

A: Introduction :Given , a channel band limited to 6 KHz SNR is 16 We have to calculate the capacity of…

Q: fine - Bandwic

A: Introduction: The maximum pace of information flow on a specific path is said as information…

Q: Plot an example for ASK, FSK and PSK wave

A: Please upvote, I am providing you the correct answer below. Please please please.

Q: 2. What is the bandwidth of a signal that can be decomposed into five sine waves with frequencies at…

A: The answer for the given question is as follows.

Q: What affects does delay skew have on the signal?

A: Intro What effects does delay skew have on the signal?

Q: The capacity of a standard 4 kHz telephone channel with 28 dB SNR

A: Given bandwidth = 4khz = 4000hz SNR(db)=28 SNR = 10(SNR(dB)/10)=10(28/10)=102.8 SNR = 631

Q: An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then…

A: Introduction :Given , signal carries 4 bits in each signal unit.1000 signal/sec sent .Then , we have…

Q: what is HZ ?

A: The full form of HZ is Hertz, and it is the unit of frequency.

Q: An analog signal carries 8 bits per signal element. If 6000 signal elements are sent per second,…

A: Given Analog signal carries 8 bits per second R=8 bits per second Baud rate =6000 bauds per second…

Q: Calculate the modulating frequency that causes an FM signal to have a bandwidth of 50kHz when its…

A: - We need to find the correct modulating frequency.

Q: If the highest frequency component in an analog signal is 20 kHz, what is the minimum sample…

A: Frequency: Knowing that, if we tend to decide that the very best frequency we're inquisitive about…

Q: Subject - computer networking The digital signal is to be designed to permit 160 kbps for a…

A: Introduction

Q: Еxample: A telephone line has a bandwidth of 3000. The signal-to-noise ratio is usually 3162. For…

A: The formula for channel capacity is c=wlog2(1+s/n) s/n is signal to noise ratio and w is the…

Q: A channel carries information at a signal-to-noise ratio of Ldb = 13 . Find the capacity of this…

A: Here We use Formula Shannon channel capacity C = B.log2(1+SNR) (in bits/second) where B is the…

Q: State Carson's rule for determining approximate Band Width of FM signal.

Q: Inverted ARP: What It Means

A: Inverted ARP (Address Resolution Protocol) refers to a technique used in some network protocols,…

Q: In the field of information technology, pulse code modulation is a technique used by codes to…

A: Introduction: In this answer, I will discuss pulse code modulation. Codes use pulse code modulation…

Q: Suppose we want to generate a PWM signal to toggle an LED every one milliseconds (1ms), which…

A: In the intricate world of microcontroller programming, generating Pulse Width Modulation (PWM)…

Q: If the bandwidth of a signal is 5 KHz and the lowest frequency is 52 KHz, what is the highest…

A: Given that: If the bandwidth of a signal is 5 KHz and the lowest frequency is 52 KHz, what is the…

Q: Suppose a signal travels through a transmission medium and its power is reduced to one-half. What is…

A: Solution

Q: Computer science What is the maximum number of slots in a TDM frame if n signal sources with the…

A: Introduction: A method of transmitting and receiving separate signals across a shared signal route…

Q: Given a channel with an intended capacity of 20 Mbps, the bandwidth of the channel is 3 MHz. what…

A: Given data: Bandwidth (B) = 3MHZ Intended capacity of the channel(C) = 20 Mbps

Q: Write a note on Bit rate and Baud rate. If the bit rate of a signal is 10 bits/second and the Baud…

Q: The power in FM signals is constant

A: The amplitude in the FM signal is constant. Average power (P) = amplitude2 / 2 (constant) The…

Q: An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are…

A: The Answer is

Q: The capacity of a standard 4 kHz telephone channel with 28 dB SNR

A: Given bandwidth = 4khz = 4000hz SNR(db)=28 SNR = 10(SNR(dB)/10)=10(28/10)=102.8 SNR = 631

Question

The range of frequencies a channel can pass is called bandwidth in Hertz why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Explanation

VIEW

Step 2: Summary

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

If the bandwidth of a signal is 5 KHz and the lowest frequency is 52 KHz, what is the highest frequency?
An analog signal carries 8 bits per signal element. If 6000 signal elements are sent per second, find the bit rate.
Example: A telephone line has a bandwidth of 3000. The signal-to-noise ratio is usually 3162. For this channel the capacity is calculated as
The power in FM signals is constant
If the highest frequency component in an analog signal is 20 kHz, what is the minimum sample frequency?
A channel carries information at a signal-to-noise ratio of Ldb = 13 . Find the capacity of this channel at 5MHz.
telecomunication engineering
Computer science What is the maximum number of slots in a TDM frame if n signal sources with the same data rate are to be sent at the same time?
State Carson's rule for determining approximate Band Width of FM signal.
Write a note on Bit rate and Baud rate. If the bit rate of a signal is 10 bits/second and the Baud rate is 5 Bauds/second. Find out the number of bits/baud.
If the channel is band limited to 6 kHz and signal to noise ratio is 16, what would be the capacity of channel? Downvote will be given to incorrect answer
Given a channel with an intended capacity of 20 Mbps, the bandwidth of the channel is 3 MHz. what signal-to-noise ratio is required to achieve this capacity?