The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine themaximum torsional stress in the shaft and its angle of twist.

The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine themaximum torsional stress in the shaft and its angle of twist.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Related questions

Q: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60 kW…

A: Given information: Hollow shaft with diameter ratio 3:4That is Inside DiameterOutside Diameter =…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

Q: The steel shaft has four gears with corresponding number of powers as shown. The allowable shear…

A: Find the minimum required diameter of shaft Allowable shear stress = 75 Mpa Allowable twist = 0.05…

Q: Q9.16 A shaft of tubular cross section has an external diameter diameter of 2.5 cm. It is made of…

Q: ). Determine the limiting peripheral velocity of a rotating steel ring if the allowable stress is…

Q: Q// The mean dimensions of the cross section of an airplane fuselage are shown. If the fuelage is…

A: Given data: Shear modulus (G) = 3.9×103 ksi Allowable shear stress = 18 ksi Angle of twist per unit…

Q: Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60…

Q: The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at…

A: Given, L=2m Do=40mm=0.04 m ro=20mm = 0.02 m Shear Stress= 140 MPa ω= 80 rad/s

Q: A generator driven by a wind turbine is required to deliver 6 MW of power at the generator…

Q: A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a…

Q: A solid shaft of 120 mm diameter transmits 80Kw power at 160 rpm. Taking modulus of rigidity of 80…

Q: * While transmitting power ofa steam turbine, the angle of twist of a rotating shaft was measured…

A: Given: · Angle of twist of a rotating shaft ∴ θ = 1.2° = 1.2×π180 =…

Q: RIO-3. The A36 stoel circular tube is subjected to a toryue of 10 kN - m. Determine the shear stress…

Q: The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer…

Q: The stainless-steel shaft shown below is solid with a diameter of 120 mm. The shaft is fixed at A…

A: Given:DIameter, d=120 mmTB=500 N.mTC=800 N.mG=75 GPa

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

Q: Axial force of 900 N and torque of 2.50 N-m are applied to shaft. If shaft has a diameter of 40 mm,…

Q: A 50 mm diameter shaft is transmitting a power of 142.8 HP and is turning at 900 rpm. The shaft is…

A: given data ; diameter = 50 mmpower = 142.8 HP = 142.8 * 746 Wrpm = 900 rpmbending stress =…

Q: -51. The engine of the helicopter is delivering 600 hp o the rotor shaft AB when the blade is…

Q: Determine the maximum shear stress of the given shaft in MPa if a T= 10kNm torque is applied to it;…

A: Given, Torque applied on shaft = T = 10 kNm = 10 x 106 Nmm Diameter of shaft = D = 75 mm Length of…

Q: A generator driven by a wind turbine is required to deliver 5 MW of power at the generator…

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 255 lb-ft and TD= 95 lb-ft,…

Q: The shaft is subjected to a distributed torque along its length of t = (10x2) N # m>m, where x is…

Q: A solid shaft is transmitting 1 MW at 250 r.p.m. Determine the diameter of the shaft if the maximum…

A: As per our guidelines we have to answer one question only so, post the question separately and…

Q: A generator driven by a wind turbine is required to deliver 2 MW of power at the generator…

A: tip-speed ratio The tip-speed ratio, λ, or TSR for wind turbines is the ratio between the tangential…

Q: The 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in.,…

A: Given: The power of the reducer motor is P=6 hp. The angular velocity of the reducer motor is ω=1200…

Q: Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree…

A: Given Data P=30 MW N=1500 rpm Angle of twist=1° L=20D G=80 GN/m2

Q: SS 304 steel shaft is 3 m long and has an outer diameter of 60 mm. When it is rotating at 60 rad/s,…

Q: A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not…

Q: Q5: Determine the diameter of the solid shaft where the angle of twist not exceed 10 and the length…

A: Given: The angle of the twist: →θ=1°=1×π180=0.017 radian Diameter of the shaft=d And length of the…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

Q: A solid shaft is transmitting 1 MW at 240 r.p.m. Determine the diameter of the shaft if the maximum…

A: Given, Power transmitted through shaft = P = 1 MW = 1 x 106 W Shaft rpm = N = 240 rpm Maximum…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

Q: The shaft is made of A992 steel and has an allowable shear stress of 95 MPa. When the shaft is…

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Find the absolute maximum shear stress

Q: When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a…

A: Given, Torsional Resistance at A = TA Distributed torque = (0,0) at B and (tA,L) at B Outer radii…

Q: A solid shaft with a diameter of 20 mm is shown below. The shaft is fixed at points A and B. In the…

A: As per given question question a) Draw a torque diagram for this shaft. b) Determine the maximum…

Q: The tubular drive shaft for the propeller of a hovercraft is 6 m long. If the motor delivers 4 MW of…

A: Given data as per the question Length of shaft =6 m Power delivered =4 MW The outer diameter of the…

Q: The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the…

A: Given: The allowable shear stress, τ = 75 MPa The speed of the shaft, N = 300 rpm The power of the…

Q: Q3.An electric motor is connected to a turbine with the help of a hollow shaft. The hollow shaft has…

Q: Determine the absolute maximum shear stress in the shaft. Express your answer to three significant…

Q: Let's consider a solid circular shaft subjected to the torque loads as shown. Determine the minimum…

Q: While transmitting power of a steam turbine, the angle of twist of a rotating shaft was measured and…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 290 lb-ft and TD= 125 lb-ft,…

A: Given data: ◆ The diameter of solid shaft: d = 1.500 in ◆ The torque applied at gear D: TD = 125…

Q: A 500 mm pulley running at 400 rpm drives another pulley of the same diameter by means of a 12 mm…

Q: a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of…

A: Shear stress produced by torque vary from zero at center of cross-section to maximum at surface in…

Q: The solid steel shaft carries the torques Tl = 750 N • m and T2 = 1200 N • m. using Ll = 1.0 = 2.5 m…

Q: A generator driven by a wind turbine is required to deliver 6 MW of power at the generator…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine the
maximum torsional stress in the shaft and its angle of twist.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad>s, determine the maximum torsional stress in the shaft and its angle of twist.
The tubular drive shaft for the propeller of a hovercraft is 6 m long. If the motor delivers 4 MW of power to the shaft when the propellers rotate at 25 rad>s, determine the required inner diameter of the shaft if the outer diameter is 250 mm. What is the angle of twist of the shaft when it is operating? Take tallow = 90 MPa and G = 75 GPa.
A solid circular shaft transmits 75 kW power at 200 rpm. Calculatethe diameter of the shaft and the maximum shear stress acting on it,if the twist in the shaft is not exceeding 1 º in 2 m length of the shaft.Take modulus of rigidity as 102 GPa.
Find out the outer diameter of the hollow shaft, if the allowable shear stress induced in it is 53MPa and the permissible value of Torque in it is 2000Nm. Take the value of k to be 0.6 k = the ratio of inner diameter to outer diameter.
A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to exceed 60 MN/m² nor the angle of twist 0.3 per metre length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m².
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3.000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a hamonic torque given by M(1) = Mo cos ot about the shaft axis with Mg = 200 N-m and as = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is h = 0.05 kg-m. Assuming the equivalent tosional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). ka M() = Ma cos e Turbine rotor, Jo A 50-kg turbine is mounted on four parallel springs, each of stiffness of 3 x 10° N/m When the machine operates at 40 Hz. its steady-state amplitude is observed as 1.8 mm What is the magnitude of the excitation? Given m = 50 kg. k = 3x 10 Nm. e = 40 Hz. X= 1.8 mm Find: Fe
A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Assume TA = 532 N-m, Tg = 1330.0 N-m, Tc= 1064 N-m, and Tp = 266.0 N-m. Determine the magnitude of the maximum shear stress in the shaft. Answer: Tmax= i D Tp (3) C Tc MPa (2) B TB (1) TA
A hollow shaft transmits 9 MW at 300 rev/min. It is supposed that the maximum allowable stress is not to exceed 70 MN/m2 nor the angle of twist 0.5 degree per metre length of shafting. If the outside diameter of the shaft is 400 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m2. *
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(1) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is J, = 0.05 kg-m?. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 0(1). O(1) M(1) = Mg cos etr %3! Turbine rotor, Jo
11 A solid steel shaft 30 cm in diameter is rotating at a speed of 300 r.p.m. If the shaft is constrained at its ends so that it cannot expand or contract longitudinally, calculate the total longitudi- nal thrust over a cross-section due to rotational stresses. The density of steel is 7800 kg/m³ and v = 0.30.
A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner diameter of 1.5 in. The shaft is transmitting 200 hp at 120 rev/min. Determine (a) themaximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106 psi for steel
Determine the diameters of a hollow shaft which has to transmit 40 kW at 300rev/min. If the shear stress is limited to 30 MPa. Assume the maximum torque to be 12% greater than the mean torque and that the shaft diameters are in the ratio of 1 to 1, 5.