The propagation time from input to output for a CMOS NAND gate with 2 inputs when it drives a load capacitance C = 0.2 fF is tp = 200 ps. Which is the propagation time tp of the gate if it drives 2 inputs of 2 other CMOS NAND gates, which have a total gate capacitance Ce = 0.8 fF? O (a) depends on the pull-up resistor. O (b) 1.6 ns. O (c) 400 ps. O (d) 4 times higher.

The propagation time from input to output for a CMOS NAND gate with 2 inputs when it drives a load capacitance C = 0.2 fF is tp = 200 ps. Which is the propagation time tp of the gate if it drives 2 inputs of 2 other CMOS NAND gates, which have a total gate capacitance Ce = 0.8 fF? O (a) depends on the pull-up resistor. O (b) 1.6 ns. O (c) 400 ps. O (d) 4 times higher.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume Vth = 1V and k = 50mA/V2. Given the schematic below, do the following: 1) Indicate and verify the state of each MOSFET and ?0 for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use ?ds,on approximation for linear operation. 2) Determine what kind of logic circuit is implemented in the circuit.
1. A circuit containing two FET transistors is shown below. The values of Va and Vb can be either 5 V (digital 1) or OV (digital 0). Similar to what we did in class, draw a table that lists the four possible combinations of Va and Vb, and the corresponding output voltage Vout. Which digital logic gate does this correspond to (AND, NAND, OR, or NOR)? 5 V ww R 5 V Va Vout ww R FET 2. Repeat problem 1 for the circuit below. Vb Vout FET Va Vb LL FET1 FET2
draw nand gate circuit diagram as well,please
A certain packaged IC chip can dissipate 5W. Supposewe have a CMOSIC design that must fit on onechip and requires 10 million logic gates. What is theaverage power that can be dissipated by each logicgate on the chip? If the average gate must switch at100 MHz, what is the maximum capacitive load ona gate for VDD =3.3 V, 2.5 V and 1.8 V.
Find the VTC of the following non inverting RTL assume Bf=100 - Vbef=0.7 v - Vbesat=0.8v Vcesat=0.2v vin Rin m VIN 1kQ VCC 5.0V RC M1KQ non-inverter gate analysis at different RC values Q1 2N2222A RE 21KQ
7) The following figure shows a transistor-level (CMOS) circuit for some logic gate. Sketch the logic gate for the CMOS gate. Choices: a) NAND gate b) AND gate c) OR gate d) NOR gate
find the output of each gate (OR - AND-NOT-NOR- NAND -XOR) by using 3 inputs (A,B,C)?
None
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th R₂ = 5600 R₁ = 4700 M3 Ao M₁ M₂ a. Indicate and verify the state of each MOSFET and V for the following input 0 combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. Example: M1 is assumed to be in saturation. If Vgs = 2 V, Vds = 4V, Vds > Vgs - Vth 4>2-1 4> 1 (ok) Vgs > Vth (2>1) A B M1 state M2 state M3 state V OV OV 5 V OV b. What kind of logic circuit is implemented in the circuit above? 5V www. V₂ 0
it's urgent please solve asap
A logic gate switches in 5ns and has a triangular shoot through current with a peak value of 8mA. Estimate the value of nearby decoupling capacitor required to limit the power supply noise due to switching to 150mV. Enter your answer in pF to 3 significant figures.
please solve this in 25 minutes . help me i will give positive feedback