The pressure vessel is fabricated from aluminum [E = 10,000 ksi; v= 0.33), and it has an inside diameter of 48 in. and a wall thickness of 0.75 in. If the internal pressure in the cylinder is 425psi, find the absolute maximum shear stress on the inner surface of the cylinder. O 8.79 ksi O 8.35 ksi O 7.01 ksi O 4.31 ksi O 7.46 ksi

The pressure vessel is fabricated from aluminum [E = 10,000 ksi; v= 0.33), and it has an inside diameter of 48 in. and a wall thickness of 0.75 in. If the internal pressure in the cylinder is 425psi, find the absolute maximum shear stress on the inner surface of the cylinder. O 8.79 ksi O 8.35 ksi O 7.01 ksi O 4.31 ksi O 7.46 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the maximum torsional stress in shaft AC shown in the following figure. Assume the shaft from A to C is 10 mm diameter
If pressure vessel is cylindrical, tangential stress is half of the longitudinal stress. O True O False
a)jj holiow steel tube jsed in a roof structure has an outer diameter, d; = 104 mm and inner diameter, dz = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MPa.
SECTION: 500mm 20 KN I5 KNIM 1000 mm 12 m Ps 800 KN e : 400 mm (ASSUME IS % LOS SES) A. Determine the stress at the bottom in the free end. (MPa) B. Determine the stress at the top in the fixed end. (MPa)
Strain gage on the surface of a thin-walled steel boiler as shown in the figureaffixed. With shape change meter εx = 500 (10-6A value of) was read. The inner diameter of the boiler 60Mm. The wall thickness of the boiler is 2mm E=200 GPa, υ=0.3 a)Calculate the stresses in the boiler b)Determine the internal pressure in the boiler
The copper pipe shown in the figure has an outside diameter of 3.000 in. and a wall thickness of 0.383 in. The pipe is subjected to a uniformly distributed torque of t = 87 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c = 7.75 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. Answers: ccccccccc.com (a) TA= a (b) TB = i b i psi psi
The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi
Problem-3 b. A water main 160 cm dia. Contains water at a pressure head of 200 m. Take weight of water to be 1000 kg/m³. The thickness of the metal shell required for the water main given that the maximum permissible stress in the metal is 400 kg/cm², will be...
During the tensile test, experiment on a sample of mild steel, data represented in the figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, the reduced diameter (d;) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inches and final Gauge Length (L) is 2.625 inches. Answer the questions below: Us TR 70- 60 - Lo LyP *IR 50 - EL PL: proportimal limit EL Elastic limit UXP = 4pper yield point Lyp : Lower us : uiti mated streagth IR : Indicanteed Strengty Rupture TR: True strength Ruptue 40 AL or 8t P 30 **PL (proportimal limt) Direct strain E strain (in/in) aStress Iblinz (esi) 0.003. ogo o-200
Q..c,.
3.) A tube with E=10x106 psi is used to support a compressive load. The maximum allowable change in length is 0.025 percent, determine (a) the maximum normal stress in the tube (b) the minimum wall thickness for a load of 1600 lb if the outside diameter of the tube is 2.0 in.