The pressure inside a horizontal domestic water pipe is 60 psi above atmospheric. If viscous effects are neglected, determine the maximum height reached by a free jet of water through a small hole in the top of the pipe. Assume atmospheric pressure is negligible. Unit weight of water is 62.4 pcf. A clean, labeled sketch with hydraulic points of interest and any Datum shown Solution steps (

The pressure inside a horizontal domestic water pipe is 60 psi above atmospheric. If viscous effects are neglected, determine the maximum height reached by a free jet of water through a small hole in the top of the pipe. Assume atmospheric pressure is negligible. Unit weight of water is 62.4 pcf. A clean, labeled sketch with hydraulic points of interest and any Datum shown Solution steps (

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.14P

See similar textbooks

Similar questions

Question 4 A 150 mm diameter pipe is connected to a large tank with a bellmouth inlet. The pipe is carrying oil (specific gravity 0.85) with an absolute viscosity of 0.0056 N-s/m² and the roughness elements of the pipe wall is estimated as k = 0.9 mm. (a) Above what flow rate will this pipe behave as a fully rough pipe? (b) Below what flow rate will it behave as a smooth pipe?
Please answer with explanation
SUBJECT IS HYDRAULICS SHOW DETAILED AND COMPLETE SOLUTION USED 3 DECIMALS FOR THE FINAL ANSWER The open tank contains two different liquids as shown below. Determine the total pressure at elevation zero. =1.3 A B ELEV. 4.5 m Liquid A spgr = 0.9 ELEV 1.0 m Liauid B spgr = 1.1 El. 0m %3D
LAB 4. THANK YOU HYDRAULICS LABORATORY
A 11 inches pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the pressure at point A in the pipe is 30 psi. A differential gage is attached to the pipe at A and at a point B downstream which is 8 ft higher than A. The deflection of mercury in the gage is 3.33 ft, indicating a greater pressure at A. What is the lost head A to B? Show the diagram.
Please don't provide handwritten solution ......
a Mud is flowing through 4 ½ inch OD/ 3.64 inch ID, internal flush drill pipe. The circulating flow rate is 400gpm and the mud properties as follows : Mud weight = 10 ppg Yield point = 10 lb/100 ft2 Plastic viscosity 30 cp 1. Calculate the pressure losses per 10,000 ft of drill pipe. 2. Calculate the pressure losses per 10,000 ft of drill pipe if use a water as a working fluids. 3. During the calculation case 2 at what velocity flow become turbulent? b The following shear stress - shear rate behavior was observed. Shear Stress (dynes/cm²) Shear rate (Seconds-') 20 11 30 15.2 40 19.1 50 22.9 60 26.5 1. Make a plot of shear stress (ordinate) vs shear rate (abscissa) on log-log paper. 2. Can the fluid behavior be accurately modeled by the Newtonian, Bingham plastic, or Power law model? 3. Compute the apparent viscosity for each shear rate. 4. Compute the yield point and plastic viscosity for each shear rate. 5. Compute the consistency index and flow behavior index.
Assignment no. 3 Problem # 1. A 300 mm diameter test well penetrates 24 m. below the static water table. After 24 hours of pumping at 69 liters/sec. The water level in an observation well at a distance of 96m from the test well is lowered 0.60m. And the other observation well at a distance of 34m from the test well, the drawdown is 1.2m. a. Compute the coefficient of permeability of the unconfined aquifer in m/day. b. Compute the transmissibility of the unconfined aquifer in m2/day. Compute the transmissibility of a confined aquifer 8m. thick below the unconfined aquifer in m2/day. I.
03. Find the pressure difference between A and B Oil RD = 0.8 Water 0.4m 0.2m 0.3m Water 0.4m 0.4m (a) 1692 Pa (b) 1913 Pa (c) 2141 Pa (d) 2551 Pa
[CE Hydraulics] 7. Using the SI units, write an expression relating Manning Coefficient, n, to the Chezy Coefficient, C. State the dimensions of both.
A pipe carries a flow of 5.17 cfs of oil (SG = 0.877). At one location where the diameter is 6 inch, the pressure is 13. 2 psi. At another location which is 12 ft higher in elevation, the diameter is 18 inch and the pressure is 8.75 psi. Determine the head loss between the two locations, and the direction of flow.
Please submit the png solution.