The power flowing in a 3-phase, 3 wire, balanced load system is measured by the two wattmeter the method. The reading on wattmeter A is 5000 W and on wattmeter B is -1000 W.(a) What power factor of the system. (b) If the voltage of the circuit is 440, what value of capacitance which must be introduced into each phase to cause the whole of the power measured to appear on wattmeter A

Q: Determine the current through, voltages across, and the power dissipated by the circuit using…

A:

Q: Find the equivalent resistance seen by the generator 10v. 52 52 Ic 10V 30 42 122 Vo 52 72 elect one:…

A:

Q: The power measured with the help of a single phase one wattmeter method in a balanced three phase…

A: We will try to find the power of the 3-phase circuit by the following analysis.

Q: Find the value of R for maximum power transfer in the network and the maximum power that can be…

A:

Q: A wattmeter is connected as shown in the figure. The wattmeter read Current coil Potential coil Z₁…

A: Given circuit,

Q: Find the average voltage from 45⁰ to 180⁰ @ Em = 100 Volts? b) what is the average current if this…

A:

Q: What is average wattmeter value of the three wattmeter method ? O a. Total power /2 O b. Total power…

A: Average wattmeter value of three wattmeter method  is given by  P= W1+W2+W3 where, sum  of W1 , W2…

Q: Three similar coils, each of resistance 10 Q and reactance 10 Q, are connected in star across a…

A:

Q: In a 3-phase power measurement using two wattmeter method, if one wattmeter reads 2.5 times the…

A: Given: In a 3-phase power measurement using two wattmeter method, One wattmeter reads 2.5 times the…

Q: Determine the currents for the giyen electrical network.

A: It is given that:

Q: In a 3-phase power measurement using two wattmeter method, if one wattmeter reads 2 times the other,…

A: Given: A 3- phase power measurement using two wattmeter method  And one wattmeter reads two times…

Q: E. Şekildeki devre için çevre akımları yöntemini kullanarak denklemleri yazınız. ww. 20 Ohm ww. 4…

A:

Q: wye-connected load has a voltage of 480 V applied to it. What is the voltage dropped across each…

A: Given,  Line to Line voltage applied to wye-connected load is VL = 480 volts

Q: Three Inductive loads each of resistance R = 28 ohms and inductance L = 0.03 H are connected in star…

A:

Q: What is the reading (in kW) of both the wattmeter, when measuring the power of a three-phase three…

A: Given- Three-phase three wire systemInput power=5 kWPower factor=0.866To Find-The reading of both…

Q: Find the equivalent resistance seen by the generator 10v. 50 50 10V 30요 122 V. 72 Select one: a. Req…

A:

Q: A circuit with three parameters connected in series R= 5 ohm,XL=j2 ohm and Z the St=36.4 volt ampere…

A: Complex power , S=36.4 VA  Power factor=0.86    cos ∅=0.86    sin ∅=0.51

Q: Given DC voltage and AC sinewave voltage in series, what would be the total power delivered to a…

A:

Q: 1. In a two wattmeter method used for measuring 3 phase power each wattmeter reads 200 kw ± 2% and…

A: Given Data:Two watt meters used for measuring 3-phase powerWattmeter 1 reads 200 kW ± 2%Wattmeter 2…

Q: Determine the maximum power (in Watts) that can be transfered to the load RL- (Use 3 decimal places.…

A:

Q: Determine the maximum power (in Watts) that can be transfered to the load RL. (Use 3 decimal places.…

A: I₁ = 1.5 A R = 4.9 ohms I₂ = 3.9 A Find :-The maximum power (in Watts) = ?

Q: The resistance in each phase of the load when the load power factor 0.8 is: 24 A R 120 V R wwm R L

A: Given load power factor =0.8 P=3VPLIPLcosΦ   =3×120×24×0.810   =6912 wpower consumed by phase one…

Q: Three loads each having a resistance of 10 ohms are connected in WYE. The total three phase power is…

A: Since, the load current is equal to the phase current. IL=Iph=VphR The line voltage is root three…

Q: Use Kirchhoff's and Ohm's current laws to determine all currents and voltages of the following…

A: According to question: Applying KCL at nodes 'b' and 'c', this will give…

Q: Find any one phase voltages if Vo = 50 260° V; V- 100 300° V and = 50 2-900° V. (Type the exact…

A: The value of the phase voltage can be calculated using the following relation

Q: Answer all questions based on the diagram below: Source -m 2400 V Load = 300 Source Voltage = 2,400…

A: In this question, we need to determine the line voltage at source and load side, phase current at…

Q: 1. A single-phase AC circuit is connected to a 100 (V) 60 (Hz) voltage source, which is shown in the…

A: In this question, we need to determine the reading of ammeter and wattmeter.We know, inductive…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.