пыты рытием по MIT MIThe point A is moving to the right at a constant speed of 18 in./s.Note that bar BC can rotate about point C. Otherwise, point A could not move.8 in.BC8 in.4 in.Knowing that point A is moving to the right at a constant speedpoint B, (b) point D., you wiIIdetermine the acceleration of (a)

Answered: Image /qna-images/answer/cc5cd7b3-9efd-4355-8317-0a711b74bd2d.jpg

The point A is moving to the right at a constant speed of 18 in./s. Note that bar BC can rotate about point C. Otherwise, point A could not move. 8 in. B 8 in. 4 in. Knowing that point A is moving to the right at a constant speed point B, (b) point D. determine the acceleration of (a)

The point A is moving to the right at a constant speed of 18 in./s. Note that bar BC can rotate about point C. Otherwise, point A could not move. 8 in. B 8 in. 4 in. Knowing that point A is moving to the right at a constant speed point B, (b) point D. determine the acceleration of (a)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A. A water jet of diameter 180 mm impinges on the buckets of a Pelton turbine having overall efficiency of 85% while operating under a net head of 500 m and at speed of 420 rpm. Find the specific speed of the turbine. Take coefficient of velocity of the jet as 0.98 and speed ratio as 0.46. B. The pitch circle diameter of a Pelton wheel is 0.9 m. A jet of water of diameter 80 mm gets deflected by an angle of 170° when it impinges on the buckets. The bucket friction coefficient and coefficient of velocity of jet can be taken as 0.93 and 0.97 respectively. If the net head available on the wheel is 500 m and speed ratio is 0.45, calculate (a) the power transferred to to the wheel by the jet, (b) hydraulic efficiency, and (c) specific speed of the turbine. Take mechanical efficiency of wheel as 0.9.
Load B is connected to the double pulley by one of the two unstretched cables as shown. The movement of the pulley is controlled by the cable C, and the cable C has a constant acceleration of 225 mm/s2 and an initial velocity of 300 mm/s2. And both directions are to the right. (a) Number of revolutions by the pulley in 2 seconds (b) Change in speed and position of load B after 2 seconds (C) Find the acceleration at point D when t=0.
Consider that at the instant shown, bar AB of the mechanical system below has a angular velocity (wAB) counterclockwise at 5 rad/s and an angular acceleration (alphaAB)counterclockwise 2 rad/s².The length of bar AB is 0.4 m and the length of bar BC is 1 m. For the instant shown, and using a "Analysis of Relative Motion", determine: (a) the speed of point B (b) angular velocity of connecting bar BC (c) the speed of point C (d) the acceleration of point B (d) the acceleration of point C
2. For a short period of time, the motor turns gear A with a constant angular acceleration, starting from rest. The cord is wrapped around pulley D which is rigidly attached to gear B. 2) if the radii are: A = 70 mm, r = 230 mm, and rp = 90 mm, the constant angular acceleration of gear A, AA is 4.4 rad/s², determine the angular acceleration of gear B, CB, in rad/s². Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. αA A P Your Answer: 1'B Answer -1'p'
A straight rack rests on a gear of radius r= 3 in. and is attached to a block B as shown. Knowing that at the instant shown 8 = 20°, the angular velocity of gear D is 4 rad/s clockwise, and it is speeding up at a rate of 2.5 rad/s², determine the angular acceleration of AB and the acceleration of block B. The angular acceleration of AB is The acceleration of block B is rad/s² clockwise. (Round the final answer to three decimal places.) in./s2. (Round the final answer to one decimal place.)
Please provide accurate answer, wrong answer will get dislikes!
The 200-mm-radius disk rolls without sliding on the surface shown. Knowing that the distance BG is 160 mm and that at the instant shown the disk has an angular velocity of 11 rad/s counterclockwise and an angular acceleration of 3.5 rad/s² clockwise, determine the acceleration of A. (Round the final answer to two decimal places.) A 800 mm The acceleration of A is m/s² →→ B 200 mm
Knowing that at the instant shown bar AB has a constant angular velocity of 6.5 rad/s clockwise, determine the angular acceleration of bar BD and bar DE. (Round the final answers to two decimal places.) 100 mm B 200 mm 75 D 175 mm The angular acceleration of bar BD is The angular acceleration of bar DE is -2.93 rad/s² clockwise. -2.93 rad/s? clockwise.
1. Knowing that at the instant shown crank BC has sconstant angular velocity of 100 rpm counterclockwise, determine the acceleration (a) of point A, (b) point D. D 100 mm 200 mm B 200 mm C
Please explain each step clearly and extensively.