The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is

The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

After the advent of Bolted Connections in the mid 1950s, Riveted connection becomes outdated.Explain in detail why Bolted connections are preferred over Riveted Connection.
Determine the IBC minimum required nailing for the following connections.Search IBC Table 2304.9.1 Fastener ScheduleGive nail size, type, and required number. In the following form (example for a)a. Joist to sill or girder, toenailb. Bridging to joist, toenail each endc. Sole plate to joist or blocking, face naild. Top plate to stud, end naile. Stud to sole plate, toenailf. Double studs, face nailg. Doubled top plates, face nailh. Top plates, laps, and intersections; face naili. Ceiling joists to plate, toenailj. Continuous header to stud, toenailk. Ceiling joists to parallel rafters, face naill. Rafter to plate, toenail
Draw a complete, clearly labeled, FBD of member AE.
1. answer basing with the new NSCP 2015 guideline codes
Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes are 2 in O 3 in 3 in 4 in 3 in 2 in PL 7/8 x 12 12 in-
Please solve with complete detailed solution. Thank you.
use autocad - Draw the structural details of the following sections (an elevation view and a side view)
A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are M20 Grade 8.8 S, determine the strength of the connection. Assume the contact surface of the bolts are blast – cleaned with Class B coatings. The connection is required not to slip at serviceability. 80 120 80 80 120 80 -13 All dimensions are in mm Figure 2: Double cover butt joint. 300 O O O O o o O o o
Concrete technology (lab)
Find the smallest net area for the plate shown below. The holes are for 1 in. diameter bolts.
Tension Member -Problem 2 9 - 4" Bolts Gusset Plate Plate thickness t = ½" 2" Tension Member A36 Steel Plate 3" P, 10" и 3" d h Compare Tension Capacity of line 2" e abcde and line An Ag fgchi 4" 4"
a] Compute LRFD 6.) Compute ASD CIVIL STEEL DESIGN ENGINEERING- BOLTED CONNECTION Sample Problem 5: The 175 x 100 x 16 mm angle shown connected to a gusset plate with three 25 mm bolts (A490) when threads are excluded from shear planes. The angle consists of A36 steel. Properties of 4 175 x 100 x 16 A36 Steel Properties of A490 bolts A = 4181 mm² t = 16 mm Fy = 248 MPa F₁ = 400 MPa Fy = 276 MPa Nominal hole dia. = 27 mm 75 T+ 100 Gusset Plate 100 F 100