The pipe flow in the following figure is driven by pressurized air in the tank. The flow rate in the pipe is 50 cu.m./hr of water. Assume friction factor of the pipe f=0.014 and pipe diameter of 50mm. Calculate the needed pressure in the tank to provide the given flow rate, in kPa. Choices 1710, 1688, 1693, 1702

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then  discharges into air as…

A: Given n= 0.013  Discharge, Q= 12 cfs  Length of pipe = 160 ft  Diameter of pipe = 4 inches

Q: A pressure gage at elevation 12 m at the side of the tank containing a liquid reads 100 kPa. Another…

A:

Q: -32 Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading…

A: Manometer- These are the devices that are used to measuring the pressure at a point in a fluid.…

Q: Problem 3. A 30 cm pipe is connected by a reducer to a 10 cm pipe. Points 1 and 2 are at the same…

A:

Q: As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum…

A:

Q: (a) determine pressure at Section-2. (b) the volume rate of flow in m³/s.

A:

Q: he pump shown in the figure adds 15 ft of head to the water being pumped when the flow rate is 1.5…

A: Diameter of pipe, Length of pipe, Pressure at A,

Q: The figure shows a portion of a hydraulic circuit. The pressure at point B must be 250psig. When the…

A: Given data: Pressure at point B, PB=200 psig   Volume flow rate, Q=80galmin   Specific gravity…

Q: Pipe 1 which is 100 mm in diameter and 350 m long is in parallel to pipe 2 which is 300 m long. Pipe…

A:

Q: Compute the pressure @ point n ( Pn ) as shown by the differential manometer in KPa if pressure @…

A: We know1mm hg=0.133322kpaso,Pm=1027.66 mm hg=137.01kpaso,Writing pressure…

Q: Q1: A pressure of 10 kPa, gage, is applied to th surface of water in an enclosed tank as showi in…

A: to find actual discharge

Q: Determine the pressure of the water in pipe A shown below if the gage pressure of the air in the…

A: Take the specific weight of water (γw) as 62.4 lb/ft3.Take the pressure of the water in pipe A as…

Q: SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in…

A: From the given problem,  the SN value was not given. I'm taking SN = 26

Q: The figure shows an inlet and outlet connected to a motor. If the pressure at A is 6.25 MPa and the…

A: step 1-

Q: 11. A 350 mm by 150 mm venturi meter is installed in a vertical pipeline carrying water as shown in…

A:

Q: The figure shows a conduit made of 1 std type K drawn copper tubing that conveys acetone at a flow…

A: Given a pipe system that conveys acetone at a rate of flow of 1.33×10-3m3/s. It is required to…

Q: Q1) Determine the difference in pressure between pipe A and pipe B. Kg m PFresh water = 1000 Kg m³…

A:

Q: For the pipe enlargement shown, the pressure at sections (1) and (2) are 56.3 and 58.2 psi,…

A:

Q: Show complete solutions and figures. The shown tank with an attached manometer contains water unit…

A:

Q: Oil (relative density or specific gravity of 0.8) flows through a pipe. the diameter is 50 cm. The…

A:

Q: 3. For the piping system shown, the flow rate is 18 ft³/s of water (p = 1.94 slugs/ft³). Compute the…

A: Calculation of Pressure drop between junction point and Discharge in Each pipe####

Q: A roof tank supplies water as shown in Figure 1. Calculate the minimum height (H) in metre required…

A: Given - Static head = 1.5m Velocity  = V1.01/s   Formula used -  Htotal = Static headHs + Dynamic…

Q: 9.95. The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head…

A: Given, Diameter of the pipes= 150mm and 50mm Velocity in the 150mm pipe, v2= 0.9m/s Pressure in the…

Q: AU- Tube manometer is connected to a closed tank as shown in the fig. Determine the following: a.…

A: pressure in a horizontal line in a u tube manometer is equal. so pressure at point 2 and point 3 is…

Q: A fluid is flowing in a pipe 20-cm∅ with a mean velocity of 3 m/s. The  pressure at the center of…

A: Given data,  Pressure at center = 35 kPa Z = 5 m Velocity = 3 m/s   To find out the total head in…

Q: A cylinder is placed in a steady water flow as shown. Calculate the pressure difference PB - PA in…

A: step 1-

Q: A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET…

A:

Q: Gasoline (sg = 0.67) is flowing at 0.11 m3/s is flowing in the pipe shown in figure 8. If the…

A: This problem is related to the Fluid Mechanics. In this question we calculate Pressure P using…

Q: A 25-mm-diameter pipe 35m long is used to convey oil. The oil has a density of 880kg/m and a…

A:

Q: Given a three-pipe system, the total pressure drop is PA PB = 150,000 Pa, and the elevation drop is…

A: The pressure drop is PA - PB = 150000 Pa  zA - zB = 5ρ = 1000 kg/m3ν = 1.02 × 10-6 m2/sec Flow rate…