Answered: The % clearance of an Otto cycle is…

The % clearance of an Otto cycle is 0.186. If the initial pressure is 33 kPag, determine the final pressure. Correct Answer: 1,797.04 ± 1%

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter33: Hydronic Heat

Section: Chapter Questions

Problem 9RQ: The device that relieves the pressure in a boiler when it is above the design working pressure is...

See similar textbooks

Similar questions

The % clearance of an Otto cycle is 0.194. If the initial pressure is 43 kPag, determine the final pressure.
Provide a complete given and computation. Include all the decimals. There are received 68,000 kg/h of steam by an ideal regenerated engine, having only one heater, of which the heater receives 15,400 kg/hr the condenser receives the remainder at 0.007 MPa. If the heater pressure is 0.96 MPa, find the state (quality or "SH) of the steam (a) at the heater entrance and (b) at the condenser entrance.
Step 3 Determine the thermal efficiency of the cycle. n = Save for Later % Attempts: 0 of 4 used Submit Answer
What is the compression ratio of an Otto cycle type engine having 20% clearance . What is the air standard efficiency of an Otto cycle engine having 20% clearance. Determine the ratio of the air standard efficiency of an Otto cycle type engine having 20% clearance ifthe ? is change from 1.4 to 1.3.
Question 2: (a) The pressure at which the steam should be reheated. (b) The thermal efficiency of the cycle. (c) Total heat input (Qin) (d) Total turbine work output (Wtur.out) (e) Draw the T-S diagram Notes: Assume the steam is reheated to the inlet temperature of the high-pressure turbine. • The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 9.5% Boiler 650 C 17.5 MPa ww Reheater High-P turbine P₁ = Ps= Preheat Pump Low-P turbine Condenser e 15 KPa
Read the questions carefully and answer with complete solution and units. Deductions will be given for incomplete units/solution. Use two decimal places for solution and final answers. Connect your solutions to the final answers given below.
High-P turbine Low-P turbine Reheater 4 Boiler P4 = P3 = Prcheat Pump Condenser The following data was given for a steam Click Save and Submit to save and submit. Click Save All Answers to save all answers. The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg 3 Find the dryness fraction of steam at state 6 to 1 decimal places.
Read the questions carefully and answer with complete solution and units.Use the steam tables provided and use 4 decimal places for solving.Final answers shown are in 2 decimal places.Draw the T-S diagrams properly with respect to the saturation line. In an ideal Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to a pressure of 10 kPa. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.)Find the quality of the steam,Qa, Qr, Wt,Wp,Wnet,efficiency,and steam rate. Final Answers must be: 74.16% ,2894.58??/??, 1774.50??/??, 1130.17??/??, 10.09??/??, 1120.08??/??, 38.70%, 3.2141??/??ℎ
3. Operate at lower condenser of a Rankine Engine. P1=50 bar (saturated) P2=½bar=0.5 bar. Calculate the efficiency of cycle and engine using Mollier chart. Can you show step by steps solution using the formula given?
Read the questions carefully before answering. Box or indicate your final answers when solving and draw your diagrams cleanly. Use the steam tables provided and DO NOT ROUND the values from the steam table. Write down the values taken from the steam table. Air undergoes Isothermal expansion in a Carnot cycle where the pressure decreases from 2.5 MPa to 1.5 MPa. This process has a temperature of 550 K and it decreases to 400 K before the Isothermal compression stroke. Find a.) Qa, b.) Qr, c.) Wnet(kJ/kg),d.)the efficiency(%), e.) draw the T-S diagram with proper label of points, and f.) the pressures before and after Isothermal compression •71.55 kJ/kg, 61.78 kJ/kg, 9.77 kJ/kg, 13.65%, 251.52 kPa and 502 kPa •80.66 kJ/kg, 58.66 kJ/kg, 22 kJ/kg, 27.27%, 492.08 kPa and 820.13 kPa •61.22 kJ/kg, 41.22 kJ/kg, 20 kJ/kg, 29.98%, 315.1 kPa and 795.55 kPa •1000 kJ/kg, 900 kJ/kg, 100 kJ/kg, 10%, 500 kPa and 1000 kPa
Otto Cycle:13. An Otto cycle has a compression ratio of 7.5. Determine the volume at the end of expansion if the volume at the beginning of compression is 0.6 m3.
Box the final answer. Write legibly. Determine the heat added to the boiler in KW for the Rankine cycle that generates wet steam at 2.15 mpa. The moisture content of the steam is 4.27%. The feedwater is supplied at saturated pressure of 0.025 mpa at 81.3 kg per minute.