Problem 10.96The pendulum consists of a disk having a mass of 7 kgand slender rods AB and AC which have a mass of2 kg/m.(Figure 1)Figure 10.2 mAof 10.8 m0.5 m-DBPart ADetermine the length L of DC so that the center of the mass is at the bearing O.Express your answer to three significant figures and include the appropriate units.L =SubmitIo =μASubmitValueMy Answers Give UpPart BWhat is the moment of inertia of the assembly about an axis perpendicular to the page andpassing through point O?Express your answer to three significant figures and include the appropriate units.UnitsμAValueUnits?My Answers Give Up?

The pendulum consists of a disk having a mass of 7 kg and slender rods AB and AC which have a mass of 2 kg/m. (Figure 1) Figure 1 0.2 m of 1 0.8 m < -0.5 m-D Part A Determine the length L of DC so that the center of the mass is at the bearing O. Express your answer to three significant figures and include the appropriate u L= Submit μA Value Units My Answers Give Up ? Part B What is the moment of inertia of the assembly about an axis perpendicular to the pag passing through point O? Express your answer to three significant figures and include the appropriate u

The pendulum consists of a disk having a mass of 7 kg and slender rods AB and AC which have a mass of 2 kg/m. (Figure 1) Figure 1 0.2 m of 1 0.8 m < -0.5 m-D Part A Determine the length L of DC so that the center of the mass is at the bearing O. Express your answer to three significant figures and include the appropriate u L= Submit μA Value Units My Answers Give Up ? Part B What is the moment of inertia of the assembly about an axis perpendicular to the pag passing through point O? Express your answer to three significant figures and include the appropriate u

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure 1 ✓of 1 L45° D 60° 4 m A If load C has a mass of 380kg, determine the required minimum diameter of the solid L2-steel rod AB to the nearest mm so that it will not buckle. Use F. S.= 1.94 against buckling. (Figure 1) Express your answer with the appropriate units. d = Li μA Value Submit Units My Answers Give Up ? Provide Feedback Continue
pls correct the given
There are 3 forces that are kept in equilibrium shown in Figure. The two forces acting has 100-lb force and 200-lb force with an angle of 35 degrees. determine the value of the third force F3
I need a quick solution within 15 minutes With my best wishesTon.
Half the cross section of the steel housing is shown in the figure. There are six 10-mm-diameter bolt holes around its rim. Determine its mass. The density of steel is 7.85 Mg/m3. The housing is a full circular part.
The mass center G of the 1370-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. GO -1388 mm 975 mm- 5 mm
Figure 6 shows a light L-shaped boom OAB which supports the 400 kg cylinder. To find the tensions in the cables AC, BD and BE and the components of the support reaction at the ball and socket joint O, obtain the matrix equation representing the 6 simultaneous equations in this format: I 0x Oy Oz TAC TBD TBE II (Note: it is fairly simple to solve the 6 equations. However, please show clearly the above matrix equation. You do not have to solve the matrix equation.)
C6a please help me with the answer and full solution
i need the answer quickly
Question 2 Determine the support reactions for the system shown, given the force P and distributed load w noted below. All dimensions are in millimetres (mm). W B 2400 3000 4000 1000 Question 2 . P- 10 kN W= 5 kN RAY kN (0 decimal places) RET kN (0 decimal plaçes) Rox AKN (0 decimal plaees) Rpy kN (0 decimal places)
I need a quick solution within 15 minutes With my best wishesTon.
In the figure shown below, the moment of inertia of the pulley is 0.80 kg-m2. Compute the (a) tension in the cord AB (b) the number of revolutions turned through by the pulley when body A has moved 5.05 m. 0.4 m B 20k A 1600 N 40 kg