The paper flow to be expected trough one section of city hall consists of the following: 30 medical records from records to marriage licenses per day. 21 certificates from printing to marriage licenses per day. 15 blood samples from marriage licenses to lab per day. 10 blood sample reports from lab to marriage licenses per day. 1 box of medical records from marriage licenses to records per week. The following load-equivalence conversions can be used: One medical record = two certificates One medical record = 1 ½ blood sample One medical record = 1/10 of a box of medical records. One medical record = 2 blood sample reports With the above information, develop a From–To Chart for this operation.

The paper flow to be expected trough one section of city hall consists of the following: 30 medical records from records to marriage licenses per day. 21 certificates from printing to marriage licenses per day. 15 blood samples from marriage licenses to lab per day. 10 blood sample reports from lab to marriage licenses per day. 1 box of medical records from marriage licenses to records per week. The following load-equivalence conversions can be used: One medical record = two certificates One medical record = 1 ½ blood sample One medical record = 1/10 of a box of medical records. One medical record = 2 blood sample reports With the above information, develop a From–To Chart for this operation.

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter4: Linear Programming Models

Section: Chapter Questions

Problem 111P

See similar textbooks

Similar questions

Amy Xia's p lant was designed to produce 7,000 hammers per day but is limited to making 6,000 hammers per day because of the time needed to change equipment betweenstyles of hammers. What is the utilization?
What is OEE and also calculate the OEE from the given data in below table Items Data Shift Length 8 Hours Breaks (2) 15 minute and (1) 30 minute Downtime 47 minutes ideal Cycle Time 1.0 seconds Total Count 19,271 widgets Reject Count 423 widgets
New Mode Y Delay A Yost-Perry Industries (YPI) manufactures a mix of affordable guitars (A, B, C) that are fabricated and assembled at four different processing stations (W, X, Y, Z). The operation is a batch process with small setup times that can be considered negligible. The product information (price, weekly demand, and processing times) and process sequences are shown below. Purchased parts and raw materials (shown as a per-unit consumption rate) are represented by inverted triangles. YPI is able to make and sell up to the limit of its demand per week with no penalties incurred for not meeting the full demand. Each workstation is staffed by one highly skilled worker who is dedicated to work on that workstation alone and is paid $15 per hour. The plant operates one 8-hour shift per day and operates on a 5-day work week (i.e., 40 hours of production per person per week). Overhead costs are $9,000/week. Q Q Product A $11 Q Step 1 Station W (12 min) Step 2 Station Z (13 min) Purchased…
A metal fabrication shop has a single punch press. There are currently three partsthat the shop has agreed to produce that require the press, and it appears that theywill be supplying these parts well into the future. You may assume that the press isthe critical resource for these parts, so that we need not worry about the interactionof the press with the other machines in the shop. The relevant information here is: Part Number Demand/year Set up Cost ($) Cost per Unit ($) Production rate/year 1 2,500 80 16 45,000 2 5,500 120 18 40,000 3 1,450 60 22 26,000 Holding costs are based on an 18 percent annual interest rate, and the products are to be produced in sequence on a rotation cycle. Setup times can be considered negligible. What is the optimal lot size of part 2?
An assembly line has 10 stations with times of 1, 2, 3, 4, 10, respectively. What is the bottleneck time? OA. 1.82% of the throughput time OB. 18.18% of the throughput time OC. 100% of the throughput time OD. 550% of the throughput time OE. 50% of the throughput time چار
Sawing 20 min/unit Sanding 20 min/unit Drilling 32 min/unit Welding 30 min/unit Assembly 93 min/unit Assembly 93 min/unit Assembly 93 min/unit A production process is shown in the figure above. The drilling operation occurs separately from, and simultaneously with the sawing and sanding operations. Welding starts when both drilling and sanding operations have been completed. After welding, a product needs to go through only one of the three assembly operations (the operations are in parallel, where parallel lines perform the exact same operation). Considering the process times at stations, what is the process time of the system (in min/unit)?
These four steps make up what is called a machine cycle but is more often known as a process loop. When it comes to machine cycles, what factors do most people prioritise? Should I be concerned that I may have to replace machine cycle parts when they wear out? Is it feasible that doubling the number of modules available would make toggling between them easier?
PT Bulan Sabit is a company engaged in fan manufacturingair conditioner with the following production datai. Setup fee = $15ii. Inventory cost per fan per year = $ 125iii. Production capacity per day = 246 fansiv. Production time per fan = 2 daysv. Fan requirement per year = 20,000 fansvi. Safety stock = 1/2 day fan productionIf PT Bulan Sabit wants to implement Kanban, then calculate the needs of the companyas follows:a) Explain the definition and purpose of kanban b) Specify production order quantity c) Calculate the container kanban that must be provided by PT Bulan Sabit Assuming the time used is per year 50 weeks and 5 days per week
Lead Time Gourmet Helper Appliance Company manufactures home kitchen appliances. The manufacturing process includes stamping, final assembly, testing and shipping. In the stamping operation, a number of individuals are responsible for stamping the steel outer surface of the appliance. The stamping operation is set up prior to each run. A run of 75 stamping is completed after each setup. A setup requires 40 minutes the parts wait for the setup to be completed before stamping begins. Each stamping requires 5 minutes of operating time. After each batch is completed, the operator moves stamp the stamped covers to the final assembly area. This move takes 10 minutes to complete. The final assembly for each appliance unit requires 18 minutes and is also done in batches of 75 appliance units. The batch of 75 appliance units is moved into the test building, which is crossed street. The move takes 25 minutes. In the final test, the 75 unit batch is tested one at a time. Each test…
Lead time to deliver order to customer is shortest in OaMake-to-order Ob. Assemble-to-order OcMake-to-stock Od. None of these
Judy’s Cake Shop makes fresh cakes to customer orders. After receiving the order by Judy’s assistant, which takes 2 minutes, Judy then takes 8 minutes tomix the ingredients for the cake and loads a cake pan for baking. Then the cake is put into the oven for 30 minutes. The oven can hold three cakes at one time. When the cake is taken out of the oven, it is cooled for 1 hour. The assistant then takes 2 minutes to pack the cake for pickup and bills the customer, which takes 3 minutes.a. What is the capacity of the process, and what is the bottleneck?b. What is the throughput time for a typical cake?c. If on average five orders are taken per hour, how many cakes are there in the process (on average)?
True or False: "Bottleneck refers to a stage in a process that limits the capacity of the entire system to produce more."