the P-V-diagram that show the gas_processes used in the Otto cycle is labeled number while the real 4-stroke IC engine is in diagram number The formula number to calculte the temperature after compression and expansion are and respectively. The formula number to calculate the power obtainable from the cycle is while that for thermal efficiency of the cycle is

the P-V-diagram that show the gas_processes used in the Otto cycle is labeled number while the real 4-stroke IC engine is in diagram number The formula number to calculte the temperature after compression and expansion are and respectively. The formula number to calculate the power obtainable from the cycle is while that for thermal efficiency of the cycle is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are required to design a spark ignition engine with a compression ratio of 9. the cycle pressure is 1 bar and the temperature is 300K. The maximum temperature in the Assuming a cold air standard process analyze the appropriate cycle. At the beginning of cycle is 2000K (a) Show the cycle on a p-v and T-s diagram (b) Calculate the heat transfer and work per unit mass of air. (c) Calculate the thermal efficiency (d)Assuming all the heat is transferred at high and low temperature what is the maximum efficiency of the cycle. Justify your answer.
Q3:A small truck has #cylinder ,4 liter compression ignition engine that operates on ir standard Dual cycle with air fuel ratio of 16:1, the compression ratio is 17 and the cylinder diameter is 14.5Cm. At the start of compression stroke Ta=50'C and Pa=100 kpa .It can be assumed the half of the heat input is added at constant volume and halt at constant pressure Calculate: 1-Temperature and pressure at each state of the cycle. 2-Indicated thermal efficiency. 4:28 PM
Diesel cycle releases 1750 J/mol ofheat. The pressure and temperature at the begin-ning of the compression step are 1 bar and 50°C,and the pressure at the beginning of the expansionis 5 bar. The working fluid is an ideal gas for whichcP= 7R/2 andcV= 5R/2. (a) What is the tem-perature at the end of the adiabatic expansion? (b)What is the heat absorbed by the engine? (c) Whatis the compression ratio? (d) What is the work doneduring the compression step?
Find the efficiency of Ideal Brayton cycle having pressure ratio of 8. What will be new efficiency if pressure ratio is changed to 10.
Draw and label the P-V diagram of actual otto cycle applied to petrol engine. Draw and label the T-s diagram of ideal Rankine Cycle. Highest temperature of gas turbine cycle is 1200K and lowest temperature is 400K. What is the pressure ratio that will produce maximum efficiency, given that specifica heat ratio k for air is 1.42?
Provide given and step by step manual solution for below problem. The efficiency of Carnot cycle operating at maximum temperature of 460 deg F is 50%. Find the minimum temperature of the cycle.
Given in Table are the pressure and temperature of the steam as it enters the turbine as well as the pressure in the condenser. The given engine operates on a simple ideal Rankine cycle, calculate the unknowns in Table. Show solution Rankine Pressure of Temperature Pressure at the Net work Heat Thermal entering the Efficiency (n) in % the steam entering the entering the condenser system (WN) boiler (Qin) turbine (Rx) turbine (t+) in MPa Engine of the steam done by the in KJ/kg in KJ/kg (Pe) in kPa in °C A 3 350 75
An engine operating on the Otto cycle principle has an initial compression temperature of 675°C and a compression ratio of 8. The pressure at this condition is 100 kPa and the cylinder volume is 0.028 m³. The maximum temperature that can be achieved by the system is 4500°C. a.)Calculate the temperature and pressure at each end of the process (point), B. thermal efficiency, C. MEP
Thermodynamics The actual cycle of a 5T diesel engine, with a displacement of 7000 cm³ , 2,400 rpm is approximate to the theoretical cycle represented in the figure below, in which the custom rectangle has the area of the same cycle. A compression ratio is 17 and the thermal efficiency is 0.597 when 26.3% of the heat is provided isochorically. It is adopted that the active liquid has ϒ = 1.35 and R = 240J / KgK. To determine a) The values of p T and v at the main points of the cycle; b) The power of the cycle. c) Expansion work.
Example 3-1: A four-cylinder, 2.5-liter, Sl automobile engine operates at WOT on a four-stroke air standard Otto cycle at 3000RPM. The engine has a compression ratio of (8.6:1), a mechanical efficiency of 90%, and a stroke to bore ratio (S/B=1.2). Fuel is isooctane with AF=14.5, a heating value of 4500 kJ/kg, and combustion efficiency ne=95%. At the start of the compression stroke, conditions in the cylinder combustion chamber are 101.325 KPA and 500C. 1.draw the cycle 2. Find Efficiency 3.performance analysis (Pressure, temperature, Qin, Qout) for all Processes
3. What are the basic components of Rankine Cycle and draw TS diagrams
EX. 3: A petrol engine is supplied with a fuel of (41868 KJ/Kg) heating value. Cylinder pressure at (30%) of the stroke and (70%) of the stroke are (1.33 bar) and (2.66 bar) respectively. Assuming the compression isobying the Law PV=const. find the compression ratio if the relative efficiency compared with that of the ideal cycle is (50%). calculate the specific fuel consumption.