The output signal from an AM modulator is: p(t) rt) art) acos(Asnt) 29.4 OS 9040 84 COS 10848 12656 1- Determine the message signal f(t). 2- Find the total power, Carrier power, and Sideband power. 3- Find the transmission efficiency. 4- Calculate the bandwidth of transmission.

The output signal from an AM modulator is: p(t) rt) art) acos(Asnt) 29.4 OS 9040 84 COS 10848 12656 1- Determine the message signal f(t). 2- Find the total power, Carrier power, and Sideband power. 3- Find the transmission efficiency. 4- Calculate the bandwidth of transmission.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sub:communication. Need solution please .
A carrier signal given by 10cos27Tx108t volt is FM modulated by single tone message 4cos2Tx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power
In an AM modulation, modulating signal is m(t) = 2 cos wmt and modulation index is given as u = 0.72 a) Sketch the AM signal. b) Şketch the frequency spectrum of the AM şignal. c) Find the bandwidth of the AM signal. d) Calculate the power of AM signal, carrier signal and sidebands
Question 3. The mathematical equation of an AM modulated signal is given as follows mA. Cos((w. + wm)t+ 2. mA. SAM (t) = A,Cos(w.t) + Cos((w. - wm)t 2 %3| Where A. = 30, m = 1, w. = 6000t, w. + Wm 7000TT, w. – Wm 5000 Find out the following > Message frequency (@m) > Power in the sidebands Sketch the spectrum of the modulated signal.
In what ways AM is different from FM? Draw the outputs of AM and PAM. Explain how these schemes differ from each other in their formats?
a.Find carrier peak amplitude (vc), carrier frequency (fc), message peak amplitude (vm), messagefrequency (fm) and modulation index (m). b.Write the equation of the VAM (t) in time domain. c.Sketch spectrum of the modulated transmitted AM signal and find the Bandwidth of theTransmitted AM signal d.
digital communicationA signal was represented using Bipolar RZ with a bandwidth of 40 kHz, then thebandwidth will be …………. If Bipolar NRZ was used.
24/ b
In an AM modulator the message signal is m(t) = coswmit+2coswm2t, and the carrier wave is c(t) = Acosw.t. The modulation index is m = 0.5. a) Determine the amplitude of the carrier wave A. b) Determine the expression of the modulated signal with the AM modulation scheme. c) Determine the expression of the frequency spectrum of the AM modulated signal and then plot the frequency spectrum.
Q7. Figure Q7 shows a modulated waveform v(t) in millivolts as a function of time t in nanoseconds. 1.5 1.0 0.5 - 0.0 -0.5 -1.0 -1.5 100 200 300 400 500 t/ns Figure Q7: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) Demodulation of this type of waveform is usually performed with an envelope detector. Describe the function of an envelope detector and sketch an example circuit. (g) What requirements on the values of the components of your envelope detector circuit are there for the successful demodulation of the given waveform? (h) Keeping the same carrier wave, the modulating wave in this example is substituted with a square wave of 50%…
ii) A single sideband AM signal (SSB-SC) is given by s(t) = 10cos(11000 πt). The carrier signal is c(t) = 4cos(10000πt). Determine the modulating signal m(t).
c) Based on the Figure 1 (c), a 240V circuit supplies power to an electrical appliance. Based on the figure, briefly interpret the scenarios if: i. Fault is detected on hot/live wire ii. Ground wire disconnected Fault breaker Hot wire Service panel The resistor symbol represents all the internal components of an appliance like a washing machine. Neutral Neutral to supply transformer Ground wire Figure 1 (c)