The optoisolatorcouple a signal from its outputcouple a signal from its inputcouple a signal from its input to itsoutputFor the circuit shown, Vc voltge is *G₁₂is using light to10 µFRe 100 kg1.2kQC₂H610 µF3:45V=9V-4.48V O-3.48V-5.48V*-2.48V!

For the above given circuit diagram we need to calculate the value of collector voltage.

The optoisolator couple a signal from its output couple a signal from its input couple a signal from its input to its output is using light to For the circuit shown, Vc voltge is * 10 μF R100 kg Re21.2kQ C₂ 10 µF 8V₁-9V -4.48V O -3.48V O -5.48V O -2.48V

The optoisolator couple a signal from its output couple a signal from its input couple a signal from its input to its output is using light to For the circuit shown, Vc voltge is * 10 μF R100 kg Re21.2kQ C₂ 10 µF 8V₁-9V -4.48V O -3.48V O -5.48V O -2.48V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Change the MOD-8 counter in Figure to a MOD-16 counter, and connect the MSB to the multiplexer E input. Draw the Z waveform. 1 ΚΩ +Vcc W 13 1₂ lo Eight-input multiplexer 74HC151 SSS 17 $₂ S₁ So MOD-8 CLK- counter •JMM
For the circuit below Junction voltage is 0.7V the +ve and -ve peak of the output waveform is +10V Vin 0 -10 V t 41₁ O +4.3,-4.3 O +5.7, -5.7 O +10.7, -10.7 O +7.3, -7.3 R₁ ww 1.0 ΚΩ D₁ 5 V Diodes are IN914. D₂ 5 V * out
Sketch out the fellowing signals: (a=7, b=5, c=8) a-) V = 15a(sin2r1000*ct) b-) V = 3b(cos(7500*ct)+3) c-) Assume that you measure the signal V1 using Digital Volt Meter(DVM) and ossiloscope. What will you read on the DVM display and oscilloscop dispaly when the input voltages are defined as 1-) V = 15a(sin2m1000*ct) 2-) V = 3b(cos(7500*ct)+3) Write down and sketch all the voltages for each case. Show all parameters, including period and maximum values of the signals. aR V AC aR V, aR What will you read at the DVM display when you read the voltages at AC mode What will you read at the DVM display when you read the voltages at DC range
O2x10-3 A O 2x10-2 A A pn junction that radiates energy as light instead of as heat is called a O photo cell O Photo diode O LED O zener diode
R₁ 1k0 R₂ 3.3kO 7 6 O a. Series regulator O b. Switching regulator O c. Shunt regulator Od. IC regulator 2 5 Figure 4 Vcc 5.5V RST DIS THR TRI Cext C1 0.047µF =0.01 μF CON VCC GND 1 U2 OUT3 LM555CM
Figure 4 b) Figure 5 shows the silicon base BJT with a Rc = 1 kQ, Rg = 10 k2, Vcc = 11 V, VBB = 6 V, BDC = 99. Determine Ig, Ic, lE, VCE and VCB- Rc 1 ko Vc 10 kn 11 V VBB 6 V Figure 5
9. Compute the bias point of the circuit depicted in Figure Vcc=2.5 V 100 ΚΩ Σ1 ΚΩ KQ₁ + 0.5 V- OVCE=738V and IC=1262A OVCE=0.738V and IC=0.001262A OVCE=0.0738V and IC=0.1262A None of the mentioned. OVCE=0.738mV and IC=1262mA
For the following circuit choose the correct output if the diodes are ideal 1.0k +10V 5V 5 V -10 V +8.95 V 0. +5 V- at V 0 5 V -18 V Vout output +5.7 V-- -5.7 V-- Output O
Question 1 Find values of the intrinsic carrier concentration ni for silicon at 0°C. O 1.5 x 1010 carriers/cm3 O 1.5 x 109 carriers/cm3 O 1.5 x 109 carriers/cm2 O 5 x 109 carriers/cm3
2 Use the figure to solve the following questions (a) Vout(pk)(b) Vdc(c) IL(d) Idiode(e) PIV for any diode(f) fout
Please solve this question early
A 100 kV, 50 Hz supply is fed to a rectifier ammeter (using a bridge rectifier) through a capacitor. The PMMC ammeter of the rectifier instruments reads 45 x 10-3 amp. What is the value of the capacitor? (a) 15.90 x 10-10 F (b) 15.90 x 10-12 F (c) 17.66 x 10-9 F (d) 17.66 x 10-11 F