THE OP AMP IN THE FIND VO IN TERMS +₁1 5V 24 кл M 16K52 -M 24K2 M Us CIRCUIT BELOW IS IDEAL. OF US. 96 кл M V N₁ + loks + - Vo

Q: Show all the steps while analyzing the following sequential circuit. Include input, Output and…

A:

Q: R1 Write Datap00O 1001 Read Data 1 DMX MUX R2 Write Register Read register number 1 R3 R4 Read Data…

A: The input of combinational circuit only depends on present input. Initially the values are 0 0 0 0.…

Q: What are the similarities and differences between two signals?

A: The 2nd signal is absolutely a noisy signal because it is not any known deterministic signal and…

Q: Quèstion 6 In order to avoid the indeterminate state of the SR latch, the JK latch was designed the…

A: In SR latch when we give S=1 and R=1 it shows the indeterminate state.  truth table of SR flip flop…

Q: QUESTION 8 How many input instructions are in this ladder rung? L1 O O O 2 3 4 Inputs o-1/1 0-1/2…

A: The ladder rung is a representation of PLC control logic which contains few inputs and a single…

Q: What are the typical parameters of Data Acquisition Boards?

A: From the given figure of data Acquisition Boards

Q: Fill the following blanks with the correct words. The parallel adder performs operation…

A: addition of the two numbers in the binary can be performed by the parallel adder or the series…

Q: Write a program in 8051 to copy the contents of code ROM addresses 0100H-0102H to internal RAM…

A: In the program microcontroller require to copy the contents from ROM address 0100H-0102H and store…

Q: If output port A = 1101 B and the "9" key is pressed, port B will read, - [Be careful to check the…

A: PORT A (OUTPUT) = 1101 B Note that D3 is the MSB. Redraw the table as per circuit diagram.

Q: A1X4 Demultiplexer has O a. 4 input lines & 1 output line O b.4 input lines & 1 select line O C.4…

A:

Q: In control system, the input signal is generally represented as

A:

Q: What will be value of the voltage Vb?

A: From the given circuit diagram, node D can be considered as reference node. So, this node will be…

Q: Question 4 The 555 timer is connected in the following circuit. What is the output state at Pin 3 if…

A: The solution is given below

Q: In the Figure, if a 3 replaces a count of 9 in the register, the linear actuator will  "    " A)…

A: Linear Actuator : A linear actuator transforms rotary movement into push or pull linear motion,…

Q: The circuit shown is a NOT a serial-in/parallel-out shift register FFO FFI FF2 FF3 CLK True O False

A: we need to answer the circuit shown is not a serial in parallel out shift register this statement is…

Q: When no key is pressed the input port (Port B) will read

A: in the given circuit the matrix connected two ports are given in which port A output is applied to…

Q: If a JK latch has J=1, K=0 initially. When the K input goes high, what will be the output?

A: JK latch is JK flip flop without clock.

Q: The instruction JE is equal to O JNZ O JNG O JZ O JNL non of all

A: An instruction is a set of commands given to computer/microprocessor to perform the operation. Types…

Q: The main difference between a register and a counter is a register has no specific sequence of…

A: In this questions we need to tell about the main difference between register and counter.

Q: In practical control system, the output is controlled by a power device.

A: A control framework is characterized as an arrangement of gadgets that oversees, orders,…

Q: If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given…

A:

Q: What is soft switching designed to avoid? A. Rising edge resonance B. Switching losses C. Zero…

A:

Q: If output port A = 1011 B and the "6" key is pressed, port B will read Port A (output) 0. 21 31 DO 4…

A: If input port A=1011 B  , and the "6" key is pressed then port B will read : options are: 1111 B…

Q: Which is correct in case of Computer controlled system?

A: Given Data:There are 4 statements regarding computer-controlled systems.Required Data:Here, we need…

Q: Which of the following statements about resistive transducer instrumentation is true? Strain gauges…

A: A resistive transducer instrument is used to measure the load, pressure or displacement.

Q: 3. F(A, B,C, D) = E(0,2, 3, 5, 7, 8, 10, 11, 14, 15)

A: GivenF(A,B,C,D)=∑(0,2,3,5,7,8,10,11,14,15)

Q: A B Question 1: Derive the equations for the next state and output (You can choose the encoding…

A:

Q: In 1-to-4 demultiplexer, how many inputs are there?

A:

Q: What are the analogue instruments in aircraft

A: Generally to indicate the location and the weather and the direction and the degree of aeroplane…

Q: LED INPUT A- SIGNAL_1 INPUT_B- OUTPUT_Y LED INPUT C INPUT D- SIGNAL_2

A:

Q: For the above input signals on T, please state the value of Q for each of the eight clock ticks.…

A: It is given that:

Q: D2 is programmed to be a logic D3 D2 D1 DO Select 1 두

A:

Q: Which of the circuits in Figures 1 through 3 is a digital circuit? Which one is an analogue circuit?…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: 1. What does it mean to be 80% calibrated? 2. What it perfect calibration? 3. How does calibration…

A: Introduction Calibration is significant because it aids in the accuracy of measurements, which is…

Q: Explain how the circuit shown in Figure 10 can be modified to create a 4-bit parallel in serial out…

A: The given figure shows the circuit of Serial IN parallel OUT shift register

Q: In control system, the output  signal is generally represented as

A:

Q: Q2. Draw a full pneumatic circuit where three input signals must exit to extend a single acting…

A: Draw a full pneumatic circuit where three input signals must exist to extend a single acting…

Q: Choose the correct instruction that will send data to an l/0 device IN AL, 60 IN 60, AL OUT 60, AL…

A:

Q: * If X= (1100101)excess-3 X=(101)octal O X=(65)decimal O X=(110000)gray O X=(1000001)binay O none of…

A: The coding techniques in the digital systems are listed as follows to represent a decimal number:…

Q: Regulators are used in control system, if output changes beyond the set limit of tolerances. Select…

A: TRUE

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.