The one-way slab shown spans 12 ft from center of support to center of support. Calculate ϕMn and determine the service live load (psf) that the slab may carry. (Assume that the only dead load is the weight of the slab.) Use f′c=3000 psi and fy=40,000psi.

Q: Calculate the Load distribution of slabs to beams 2, 3 and A using 10kPa load multiplied by the…

A:

Q: Problem (2): For the one-way slab shown in Figure 1, determine and show the reinforcement values on…

A: D=150 mmd = 150-20=130 mmL =4.2 mMidspan Sagging Moment =19.3 kN.mSupport Hogging Moment = 27…

Q: - 24 in.-20 in.→ 20 in. 16 in. 8 in.] 8 in.

A:

Q: Design a rectangular beam section for the condition given below. Use 28 MPa and f = 42O MPa, and…

A: Solution: Given Data: fc'=28 MPafy=420 MPaDead Load, WD=20 kN/mLive Load,WL=12 kN/m Section size is…

Q: Replace the distributed loading by an equivalent resultant force, and specify its location on the…

A: Consider the following figure:

Q: force EG = 164414kN) force is acting on a rectangular foundation where X dimension is 2m and Y…

A: Force acting on the rectangular foundation P= 164414KN, Dimension of foundation = 2m×4m Therefore,…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: Situation: A T-beam is reinforced with 8-32mm diameter tension bars with an effective depth of…

A: Solution: Given: d = 700 mm b = 350 mm h = 800 mm t = 100 mm flange width = 750 mm fc = 27.60 MPa fy…

Q: H.W. A concrete slab, 40 ft long, 11 ft wide, and 9 in . thick, is placed on a subgrade having a…

A:

Q: Consider excavation of a simple long trapezoidal pit with a joint highlighted in the pit slope,…

A:

Q: Analyze and design Panel II of the slab shown below using ACI Moment  coefficient    method . The…

A:

Q: Calculate the unfactored slab load in KN/m

A:

Q: Figure Q1(a) shows a 3.5 m height of 150 mm x 250 mm column, is supporting á vertical load at the…

A:

Q: 2. An axial load P is supported by a short W8x40 column of cross-sectional area A=11.7 in? and is…

A:

Q: Figure (a) shows a subgrade with load cross section subjected to a rigid plate bearing test 8000 Ib.

A: Since the question number to be solved is not specified, the solution for Question a is as follows:…

Q: Determine average shear stress for rectangular cross section if maximum shear stress value is 22 MPa

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: A wall footing supports a 314 mm thick reinforced concrete wall with a dead load 312.37 kN/m and a…

A: The foundation is one of the most important parts of the construction. The foundation is defined as…

Q: A slab shown supports the load W1 and W2 for every one-meter strip along the longitudinal section.…

A: Given: The value of L is 15 m. The value of w is 145 kN/m. Consider the figure,

Q: Find the an equivalent resultant force and specify the location (x,y) of the equivalent resultant…

A: Consider the figure,

Q: 11. Determine the moment of inertia of the fully- cracked transformed section, I (in 10 mm). 12.…

A:

Q: What is the shearing stress developed at the neutral exis of the beam with a circular cross section…

A:

Q: A wall footing supports a 320 mm thick reinforced concrete wall with a dead load 297.17 kN/m and a…

A: One-Way Reinforced Footing: These are the wall footings. The principal reinforcements in these…

Q: A 60-meter building is subjected to horizontal wind loads exerting uniform pressures on the vertical…

A: Wind load is the weight put on the outside of a structure by wind in pounds per square foot. This is…

Q: SITUATION B: The beam is to carry an Ultimate Moment of 580 kN-m, geometrical property of the beam…

A:

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: Problem 8 For beam and loading shown, consider section n-n and determine (a) the largest shearing…

A: Step 1:Step 2: Therefore the answers are provided. The exact answer may be varying in some points.…

Q: Solve: A 130-mm-thick-one-way slab is reinforced with 12-mm-diameter tension bars spaced at 110 on…

A: Given data : Thickness = 130 mm Diameter of tension bars = 12 mm , Spacing = 110 Concrete cover = 20…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cr section…

A:

Q: XXe A concrete beam is post-tensioned by a cable carrying a pre-stress of 900 N/mm². At the jacking…

A: Given data- A post-tensioned concrete beam- Prestress = 900 N/mm2, Slip = 8 mm, Es=210 kN/mm2, To…

Q: Consider a rectangular footing and loading conditions shown in the figure below. The foundation…

A: Foundation rests on the ground.Load= 300 kNMoment about y axis = 400 kNweight of the footing - 450…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A: Given data Diameter of circular cross-section(D)=17mm  Shear force ( V) = 23 KN = 23 * 103 N  Now…

Q: A 300 mm thick, 2.0 m wide footing slab supports a 200 mm thick concrete wall carrying uniform…

A: Hi! Thank you for the question As per the honor code, We’ll answer the second question since the…

Q: All Two simply supported slabs: square and circular. They are istropically reinforced and subjected…

A:

Q: Q- In LSM instead of 0.002 strain in parabolic stress section, it is assumed that new strain for…

A: Given- In LSM instead of 0.002 strain in parabolic stress section, New strain for parabolic stress…

Q: A prismatic beam having 275 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ16 mm with…

A:

Q: The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit…

A:

Q: 1. If "W" is the uniformly distributed load on a square slab with "L" dimension, fixed at its ends.…

A: As per our guidelines we are supposed to answer only one question.

Q: Use E 200 GPa. Pipe External Diameter, Do

A: Using relationσ=PAreaσ=65MpaP=400kN=400,000NArea=π42002-Di2

Q: r the slabs supported on four sides, when the ratio of the longer side and shorter side exceed be…

A: As per guidelines we need to answer only 1st question so please repost rest questions separately.

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: A column is supported on a footing as shown in the figure below. The water table is at a depth of 10…

A: Given a column, Factor of safety = 3.

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.