The number of winding in primary coil of the transformer is Np = 2177. If the system is expected to produce constant 9 volts output voltage, calculate minimum number of winding in the secondary coil (Ns). - If the peak voltage produced by the bridge is greater than 9 V (for example 14 volts), what will happen to the IC 7809? For problem b, will be the load get higher power (compared with another condition where the bridge produce maximum voltage as 9 volts)? Why? If you have a 9 volts DC power supply and you get 10.6 volts output when no load is driven, what is the missing component in the power supply? a. b. C. d.

The number of winding in primary coil of the transformer is Np = 2177. If the system is expected to produce constant 9 volts output voltage, calculate minimum number of winding in the secondary coil (Ns). - If the peak voltage produced by the bridge is greater than 9 V (for example 14 volts), what will happen to the IC 7809? For problem b, will be the load get higher power (compared with another condition where the bridge produce maximum voltage as 9 volts)? Why? If you have a 9 volts DC power supply and you get 10.6 volts output when no load is driven, what is the missing component in the power supply? a. b. C. d.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no- load voltages in the primary and secondary circuit are 200 and 400 volts, respectively, and at a frequency of 50 Hz. The primary no-load current at a voltage of 200 volts is 0.7 amps and the losses in the core are 70 watts. The resistance and reactance of the primary are 3.2 and 1.25 ohms, respectively. Secondary resistance and reactance 6. 0, 0.07 ohms, respectively. Draw the equivalent circle, showing the values of its elements.
The efficiency of a transformer will be maximum when ........................? (A) copper losses = hysteresis losses (B) hysteresis losses = eddy current losses (C) eddy current losses = copper losses (D) copper losses = hysteresis losses plus eddy current losses (E) None of the above.
A 11000/230 V, 150-kVA, 1-phase, 50-Hz transformer has core loss of 1.4 kWand full load copper loss of 1.6 kW. Determine (a) the kVA load for max. efficiency and(b) the value of max. efficiency at unity power factor
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuits are 200,400 volts, respectively, at a frequency of 50 Hz The primary no-load current at voltage 200 equals 0.7 amps and pulp losses equal to 70 watts Primary resistance and reactance 3.2 , 1.25 In order, the reactance of the resistance and the coil 0.6 , 0.7 Then draw the equivalent circle, explaining the values
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs=0.0082 RHs=2.62 Rfe-HS=50002 XLs=0.015N XHs=5.2N Xm.Hs=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
4.) A transformer has a primary coil with 300 windings, and secondary coil has 400 windings. The input AC power supply is 120 volts (Vrms). A) Is this a step-up or step-down transformer? B) What is the rms voltage across the output terminals (Vrms)? C) What is the peak voltage across the output terminals (Vmax)? Primary Secondary imm ac input
The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W. Round your answer off to the nearest whole number
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
Find the elements of the equivalent circuit attributed to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 volts and 400 volts, respectively, with a frequency of 50 Hz. The primary no-load current at the voltage of 200 volts is 0.7 amperes and the loss of the core is equal to 70 watts. The resistance and reactance of the primary are 3.2 ohms and 1.25 ohms, respectively. The resistance and reactance of the secondary are 0.6 ohm and 0.07 ohm, respectively. Draw the equivalent circle, showing the values of its elements.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Consider the following open circuit transformer as shown in figure below which operate at: the voltage sources at no load (Voc)=170 V no load current (Ioc) = 85 m A iron losses power (Poc) = 14 W power factor = cos∅= 0.968 Compute the No load transformer parameter magnetizing (Im) and copper losses current (Ic) , (R0) and (X0) ?