Q.2) The cylinder consists of spirally wrapped steel plates that are welded at theseams in the orientation shown. Assume B=620. The cylinder has an outsidediameter of 265 mm and a wall thickness of 7 mm. The ends of the cylinderare capped by two rigid end plates. The cylinder is subjected to tension axialloads of P = 45 kN and torques of T = 51 kN-m, which are applied to the rigidend caps in the directions shown.Determine(a) the normal stress perpendicular to the weld seams.(b) the magnitude of the shear stress parallel to the weld seams.(c) the absolute maximum shear stress on the outer surface of the cylinder.TPT

Given: P= 45 kN T=51 kNm do=265 mm t=7 mm di=265-14=251 mm TO determine: Normal stress…

Answered: the normal stress perpendicular to the…

the normal stress perpendicular to the weld seams. the magnitude of the shear stress parallel to the weld seams. the absolute maximum shear stress on the outer surface of the cylinder.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded (longitudinal and transverse welds) on one leg (shorter leg) togusset plate; thus, there are no holes. The length of the longitudinal welds is 150 mm. Which of the following most nearly gives the allowable tensile load?
How many categories of weld are associated with Weld symbols
A shaft with two diameters connected by a fillet is shown below. In the diagram, di - 45 mm, d2- 50 mm, and the fillet weld has a radius of 7.2 mm. If the shaft is used to transmit 2400 W at 250 rpm, what is the maximum shear stress in the shaft? d2 d1
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
Describe the process carried on the Hall-Héroult with identifying the required processing ratio of the raw materials ?
The figure shows a solid 2-inch diameter roller that is attached to the wall by means of a permanent clamping. Specify the weld size for the case where the maximum allowable shear stress is 18 kpsi.
i need the answer quickly
I need the answer as soon as possible
Find. The weld sizé W for the welted.join .shawai figure T=2 Nimっ below where aaill =3.MPag Tall=1.5 Mfa F=500 N ..in. D = l00 mm 2 6. =300M m %3D Ans: h=9.1 mm 4s0.707t A TO @ab ending
T3.2.1 The bracket shown below is to support a total load (equally divided between the two sides) of 60 kN. Using E60 series welding rod and safety factor 3.0, what size weld should be specified? [Ans. 7 mm] 60 KN 100 mm 75 mm 55 mm) Note: Each plate has two 75 mm welds and one 100 mm weld.
What weld section properties are required to analyze the weld between the horizontal tube and the vertical I-beam? O a. A O b.I O c. J O d.J,A O e. A, J, I O f. I.J
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)