The next two questions refer to the cycle in the diagram shown for 1 mole of a monatomic ideal gas, where the process c -> a is adiabatic and the compression ratio for the cycle is r=4. If you can't see the figure, a PDF is here: Q6pic.pdf We are given the following information: Tc = 100K, Qa->b = 15.7kJ, Qb->c = -11.3kJ

The next two questions refer to the cycle in the diagram shown for 1 mole of a monatomic ideal gas, where the process c -> a is adiabatic and the compression ratio for the cycle is r=4. If you can't see the figure, a PDF is here: Q6pic.pdf We are given the following information: Tc = 100K, Qa->b = 15.7kJ, Qb->c = -11.3kJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown in the figure below is the cycle undergone by a Heat Pump. Your heat pump runs using 38.55 moles of monatomic Helium gas. At point a in the figure, the temperature is T₂ = 321 Kelvin and the pressure is Pa = 216000 Pascals. During the process a→b, the Volume of the system Quadruples. P Cv= Cp Y = C с a STATE a b isothermal P (Pa) b V Joules/(mole. K); Joules/(mole K); V (m³) T (K) PROCESS W (J) a-b b-c c-a Total Qhot = Qcold = Performance Coefficient = Joules; Joules; Q (J) AU (J) Activate Windows Go to Settings to activate Window
One-quarter Ibmol of oxygen gas (O2) undergoes a process from p1 = 20 lb;/in?, T1 = 500°R to p2 = 150 Ib/in?. For the process W = -500 Btu and Q = -152.5 Btu. Assume the oxygen behaves as an ideal gas. Determine T2, in °R, and the change in entropy, in Btu/PR.
In a cylinder of an automobile engine, immediately after combustion the gas is confined to a volume of 53.0 cm³ and has an initial pressure of 3.60 × 106 Pa. The piston moves outward to a final volume of 300 cm³, and the gas expands without energy transfer by heat. (Assume the gas in the engine is diatomic with y 1.40.) (a) What is the final pressure of the gas (in kPa)? = 317.920813906 kPa (b) How much work is done by the gas in expanding (in J)? 238.559389571 J (c) What If? If the engine operates in an ideal Otto cycle and 0.0125 mol of fuel-air mixture is injected into the cylinder during the intake stroke, what are the temperatures (in K) at points A, B, C, and D of the cycle as shown in the figure? P TA TC Adiabatic C processes ΤΑ A B TB То Тр = = = || B V V2 V₁ K K K K K
Required information On the property diagrams indicated below, sketch (not to scale), with respect to the saturated liquid and saturated vapor lines, and label the following processes and states for refrigerant-134a. Use arrows to indicate the direction of the process, and label the initial and final states. Use data from the steam tables. On the T-v diagram, sketch the constant-specific-volume process through the state T= 20°C, v= 0.02 m/kg from P = 1200 kPa to P2 = 300 kPa. For this data set, place the temperature values at states 1 and 2 on its axis. Place the value of the specific volume on its axis. Please upload your response/solution by using the controls provided below.
A gas whose composition is not known has 42.2kJ of paddle work input at constant volume of 566L. Initially, P1=158kPaa, T1 = 29.7oC; finally, T2=92.2oC. What is ΔU and Q if k=1.21? concert Celsius to kelvin
1. Kittel Ch3-1. Free energy of a two state system. (a) Find an expression for the free energy as a function of 7 of a system with two states, one at energy 0 and one at energy E. (b) From the free energy, find expressions for the energy and entropy of the system. The entropy is plotted in Figure 3.11.
For methyl choride at 100 °C the virial coefficients are B= -242.5 cm3/mol and C= 25,000 cm/mol?. Calculate the work of a mechanically reversible, compression of I mol of methyl chloride from 1 bar to 55 bar at 00°C. Base calculations on the following farms of the virial equations: a. Z =1+(B/V)+(C/V²) b.Z =1+ B'P + C'P2 where B' = B/and C' = (C-B'²)/(RT)² %3D %3D
In the boiler of a steam engine the superheated steam is at 500 degrees Celsius and 20 mPa is created by adding an amount of heat to the pressured water. Erros up to 10% have come up. Find the ideal gas law. Could the error seen in testing be due to the ideal gas law assumption? - value from the ideal gas law - value from tables - %Error Which of the above values is the most accurate? Could the error seen in testing be due to the ideal gas law assumption?
An amount of an ideal gas undergoes the process shown in the diagram below. Assume that during the entire cycle, the number of moles of the ideal gas stays constant. Р. A В V (a) What are the signs of Way the gast Q, and AEint for the process CA? positive positive Wby the gas AEint zero (b) What are the signs of Wby the gas Q, and AEint for the process AB? negative negative zero W by the gas AEint (c) What are the signs of Wby the gas: Q, and AEint for the process BC? Wby the gas positive Q negative DE int zero
Can you provide the step-by-step solution how to get the answers? Steam flows adiabatically through a nozzle from 1517 KPaa, 290 °C, to 965 KPaa. Sketch the pV and Ts diagram and for m=454 gm/sec, Determine delta s, delta u, delta v, delta h, work nonflow and work steady flow. the first three (delta s, delta u, delta v, delta h) were already answered. Can you continue the bold part
One mole of an ideal gas is heated slowly so that it goes from the PV state (P, V;) to (2P;, 2V;) in such a way that the pressure is directly proportional to the volume. (a) How much work is done on the gas in the process? (Use any variable or symbol stated above along with the following as necessary: n and R.) W = (b) How is the temperature of the gas related to its volume during this process? (Do not substitute numerical values; use variables only. Use the following as necessary: n, R, V, Vi, and P.) T = Need Help? Read It
QUESTION 3: |6] A cylinder that contains X kg (X = the first 2 digits of your student number divided by 330) of carbon dioxide (with molar mass 44 kg/kmol), occupying a volume of 0.025 m² at 1.1 bar, is compressed reversibly until the pressure is Y bar (Y = sum all digits of your student number divided by 10). Calculate the final temperature, the work done on the CO,, and the heat supplied when the process is isothermal.