The network function of a circuit is H(w) = 10(2 + jw) (2000 + jw) (20+ jw) (200 + jw) Sketch the asymptotic magnitude Bode plot corresponding to |H(w)|. Clearly indicate the slopes (dB/decade) in the plot. Also clearly mark the gains at low or high frequencies in the 20logio magnitude plot. Also determine and indicate where your poles and zeros are. Indicate also the type of the pole and zero.

The network function of a circuit is H(w) = 10(2 + jw) (2000 + jw) (20+ jw) (200 + jw) Sketch the asymptotic magnitude Bode plot corresponding to |H(w)|. Clearly indicate the slopes (dB/decade) in the plot. Also clearly mark the gains at low or high frequencies in the 20logio magnitude plot. Also determine and indicate where your poles and zeros are. Indicate also the type of the pole and zero.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For this problem, let x(t)= tri(t/T), where T-1msec. . Find the energy in xt), (t). J-00" b. Find the spectrum, X(f) = F(x(t)}. c. Find the absolute bandwidth in Hz. d. Find the null bandwidth in Hz. e. Find the equivalent bandwidth in Hz. f. Find the 98% energy bandwidth in Hz. Find the -20dB level bandwidth in Hz.
Signals and systems
Electrical Engineering will upvote . Need matlab knowledge these are the parts that need to be answered. ons: Calculate the cutoff points. Show a screenshot of your circuit. Are the calculated cutoffs being reflected on the theoretical Bode Plot? Include a screenshot of your codes and the theoretical Bode Plot with both cutoff points labelled. How well did the filter perform when processing the 10HZ and 15OHZ combined signal? Include a screenshot of the Scope. The transfer function for the band pass filter is given to you (equation 9). How was this derived? Show the steps starting from how you use the circuit to get the equations representing the circuit to how you solve the equations to get the final version. Given is that it is an RC Bandpass circuit with r1=10kohm, r2= 100kohm ,c1=1uf ,c2=0.001uf. the RC bandpass circuit proceeses 10hz and 150 hz combination. equation 9 needed for part 4 mentioned above is wC1 R Vw? (RCi+R1C2+R2C2)²+(1–w?C,C2R, R2)2 %3D
Question: In commutation method the charged capacitor momentarily reverse biases the conducting SCR and hence the chopper gets turned off. Option 1: Both current and voltage Option 2: Voltage Option 3: Current Option 4: lone of the above
Hi sketch the Bode plot or Aus Auso- 16 (lej F/3)( lag f/50)
-3. Determine the Ayquist rate for each of the Co following signals assuming the dyquist. nate for act) is fs Hz. of offs Bad/sec, a) gixel) b) 4₂ (4)= c) (z (t) = d) fult) = dae(t) dz 2<² (t) xelt) cos & fs t
A series circuit contains an inductance of 0.1062 mH, a capacitance of 106 pF and a resistance. At resonance, the impedance is 10 Q. Determine the Q-factor and the bandwidth at resonance.
A coil of negligible resistance and inductance 100 mH is connected in series with a capacitance of 2µF and a resistance of 10 ohm across a 50V, variable frequency supply. Determine the resonant frequency, the current at resonance, the voltages across the coil and the capacitor at resonance, and the Q-factor of the circuit
Can anyone help me with this question
If vsig is a triangle waveform, determine the maximum amplitude that vsig can have? Showyour calculation.
753. For the transfer function (TF) 4s/(s+9) and resulting Bode Plot, calculate the gains (dB) at the corner, one decade below, and one decade above. Also calculate the phase (deg) of the TF at the same three frequencies. Last answer is w_corner (rad/sec) ans:7 Repeat Ex. 753 using asymptotic approximations. ans:6
i need the answer quickly