The motor produces a torque of T = 20 N • m on gear A. If gear B is suddenly locked so it does not turn, yet C can freely turn, determine the angle of twist of F with respect to E and F with respect to D of the L2-steel shaft, which has an inner diameter of 30 mm and an outer diameter of 50 mm. Also, calculate the absolute maximum shear stress in the shaft. The shaft is supported on journal bearings at G at H. 100 mm 30 mm G E H 60 mm D 40 mm F 0.8 m 0.4 m T0.2 m |0.2 m

The motor produces a torque of T = 20 N • m on gear A. If gear B is suddenly locked so it does not turn, yet C can freely turn, determine the angle of twist of F with respect to E and F with respect to D of the L2-steel shaft, which has an inner diameter of 30 mm and an outer diameter of 50 mm. Also, calculate the absolute maximum shear stress in the shaft. The shaft is supported on journal bearings at G at H. 100 mm 30 mm G E H 60 mm D 40 mm F 0.8 m 0.4 m T0.2 m |0.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB if its axial stress is limited to 120 MPa. (b) Determine the shearing stress in the pin D if its diameter is 20 mm. B 30° 260 mm- 180 mm A 3. C D 140°. DOUBLE 28 KN SHEAR
Sir make it ass oon
The solid 27 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 800 N, Q = 850 N, LAB = 650 mm, LBC = 900 mm, LCD = 900 mm.
i need the answer quickly
The solid 32 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 500 N, Q = 1000 N, LAB = 600 mm, LBC = 800 mm, LCD = 800 mm.
The solid 36 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 500 N, Q = 800 N, LAB = 600 mm, LBC = 850 mm, LCD = 850 mm.
Solve it correctly
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
For a helical spring the slope of helix may be assumed small, is required to transmit a maximum pull of 1 kN and to extend 10 mm for 100 N load. The mean diameter of the coil is to be 100 mm. The diameter of wire is 100 mm. Calculate the no. of coils required? (G = 100 GPa and fs = 100 MPa)
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"
The bell-crank mechanism is in equilibrium for an applied load of P = 34 kN. Assume that a = 240 mm, b = 140 mm, and 0 = 63°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 6 mm. Calculate the bearing stress in the bell crank at pin B. F₁ Bell crank B a Support bracket Part 1 Use equilibrium to determine the magnitude of the reaction force at pin B. Answer: B = i kN
If the clamping force at G is 900 N, determine the horizontal force F that must be applied perpendicular to the handle of the lever at E. The mean diameter and lead of both single square-threaded screws at C and D are 25 mm and5 mm, respectively. The coefficient of static friction is μs = 0.3.