The motor delivers a torque of T = 60 N-m to the shaft AB. Thistorque is transmitted to shaft CD using the gears at E and F. Thebearings B, C, and D allow free rotation of the shafts.Figure▼50 mm35 mmPart A30 mmBT =SubmitPart BDetermine the equilibrium torque T on shaft CD(Eigure 1)Express your answer with the appropriate units.DμAValue▼ Part C1Request AnswerHÅ(TAB)max = ValueSubmit Request AnswerDetermine the maximum shear stress in AB shaft.Express your answer with the appropriate units.μÃC125 mm(TCD)max = ValueSubmit Request AnswerUnitsDetermine the maximum shear stress in CD shaft.Express your answer with the appropriate units.3PHIEUnits0UnitsB< 1 of 1?DAME??

It is required to determine the torque on shaft CD and maximum shear stress in the shaft AB and CD.…

Answered: The motor delivers a torque of T= 60…

The motor delivers a torque of T= 60 N-m to the shaft AB. This torque is transmitted to shaft CD using the gears at E and F. The bearings B, C, and D allow free rotation of the shafts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi
Please and thank
The pinion (gear 2 on shaft a) rotates at 635 rev/min clockwise and transmits 1305 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 2 mm, and gears 4 and 5 have a module of 3 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. The figure is not to scale. Please give your answer in units of newtons. geard 615 verimin m₂ = M₁ = 2mm 187 327 187 487 MG M₁ = ₂ = 3mm 0=20° I solved it and дог 692.60 Х សុំ But fr is not correct
The shaft is made of A-36 steel. It has a diameter of 1 in. and is supported by bearings at A and D, which allow free rotation. Determine the angle of twist of gear C with respect to B.
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
Problem 2: Consider the two gears mounted on the shaft, as shown. Distances are L1 = 100 mm, L2 = 250 mm, and L3 = 175 mm. Diameter of shaft AB is 15 mm, diameter of shaft BC is 20 mm, and diameter of shaft CD is 17.5 mm. Young's modulus for each portion is 200 GPa. Determine the displacement of point D with reference to point A. Also, determine the displacement of point A relative to C. b. Determine the axial strain at any point in shaft segments AB, BC and CD, respectively. If Poisson's ratio for the material of the shafts is v = 0.2, determine the lateral strain in each of the shaft segments. Based on your answers to part (a), do the gears move towards each other, or do they separate from each other? Note that in real gearboxes, movement of gears towards or away from each other is prevented by using thrust bearings. 10 kN 4 kN 5 kN 7 kN 4 kN NY 0I 17.
With the torques shown and the value of G= 9543 ksi. What would the diameter need to be of the shaft in order to make sure that the the top end of the two cylinders is not allowed to twist by a degree of greater than 1.5 deg. Torque 2-)5 1614 Torq ue 1 217516/6t 3,354 4. 35FA
Establish the relationship, to define the torque pairs to which the segments "AB" and "BC" are subjected. A T B C Tc
The shaft ABCDE is under equilibrium. Determine the internal torque in section (3). 39.00 N-m 37.00 N-m 16.00 N-m 6.00 N-m (3) Select one O a 16 N.m O b.-16 N.m Oc 10 N m Od-10 N.m e. 37 N.m f. None
I need the answer quickly
PLEASE ANSWER ?? ?Part 1 Calculate the polar moments of inertia in segments (1) and (2). Please Answer: J₁ = in.⁴ J₂= in. ⁴ ?Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Please Answer: T₁ = Ib-ft, T₂= Ib-ft. ?Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Please Answer: τ₁ = psi, τ₂ = psi ?Part 4 Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. ?Part 5 Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad. Thank you so much in advance