The molecular weight of a polymer determined by an osmotic pressure measurement in a theta solvent is 20,000. What osmotic pressure (atm) would be expected at a concentration of 1.20 g/dL and 30Centigrade ? Would there be a difference in molecular weight if the osmotic measurement were made in a good solvent ?

Q: What is the Reynolds’s number for the fluid exiting the device at 23 degrees celsius for the same…

A:

Q: What is a.) the number of transfer units  needed? b.) What is the height of the tower?

A:

Q: Find out the mass of Ethane (in pound) available in the container with volume of 80 m3 at room…

A: The mass of Ethane is to be calculated, which is kept in a closed container of a given volume at…

Q: Paint When the gas is not flowing, the pressure is the same everywhere in the pipe. How high above…

A: (a) Write the pressure balance equation as follows: Pg - ρgh1 = 0      ......1   Let, h = h1 + h2…

Q: 1. In the benzene plant, the pressure drop at some point of a pipeline in which benzene is passing…

A: ρbenzene = 876 kg/m3 ρwater = 997 kg/m3 ρCCl4 = 1587 kg/m3 Water hight left side = 4 cm = 0.04 m…

Q: A cylindrical container, 80 cm in diameter is initially filled with water to a depth of 119.367 cm.…

A: Given data: Diameter of tank = 80 cm Level of water in the tank = 119.367 cm Initial amount of salt…

Q: Q1: The absorption of ammonia from a mixture of ammonia and air containing 10% of ammonia by volume,…

A:

Q: Question: Calculate the osmotic pressure of 5% solution of urea 100 ml at 273 K.

A: Given thatVolume ,V  = 100 ml T = 273 k 5 % solution of urea

Q: Answer this: What is the concentration of a solution with a volume of 2.5 liters containing 660…

A: Molarity is defined as the number of moles of solute present in a unit volume of solution. Molarity…

Q: Q1/ Water base mud has density 9.5ppg , include bentonite only , calculate the following :- 1-…

A: Given Mud=Water+bentonite Mud  density= 9.5ppg Find 1- %Vol of bentonite in mud . 2-%Wt of…

Q: 1. Calculate the apparent molar concentrations (m) of sodium chloride solutions by using density.…

A: Given :Sodium chloride   and Water

Q: For oxygen at 25C, the collision diameter is 0.361 nm. What is the mean free path at 1 bar pressure?…

A:

Q: a. Water at 20 °C with a mass flow rate of 1.0 kg/s enters an annulus formed by an inner pipe having…

A:

Q: It is required to transport a hydrocarbon as a two-phase mixture of liquid and vapour along a…

A: It is given that a two-phase mixture of hydrocarbon is being transported in a smooth-walled…

Q: hindered settling velocity

A:

Q: For counter-current absorption in a packed column, it was found that the liquid and the gas…

A:

Q: A prevailing pressure of one standard atmosphere will support a column of mercury 760 mm in height.…

A:

Q: What is the vapor pressure of the solution in problem number 3 if the vapor pressure of pure water…

A:

Q: What is the relative mobility of carbon tetrachloride to water? The density of carbon tetrachloride…

A: Density of carbon tetrachloride at 20 0C = 1.595 g/cm3 Viscosity of carbon tetrachloride at 20 0C =…

Q: A rough rule of thumb in polymer solution theory is that a 4 molar aqueous polymer solution will…

A:

Q: A large tank of water containing 800 ppm salt is connected to a tank distilled water through a…

A:

Q: 2) A capillary has a diameter of 15 um and a length of 0.25 m. In an open system, a gaseous mixture…

A: Given: diameter of pore d =  15×10-6 m Length L = 0.25 m Pressures P1, P2, P3 are 0.005, 0.5, and 50…

Q: Calculate the radial velocity of a 60-μm-diameter soluble coffee particle in air at 250 °C entering…

A:

Q: The mass transfer rate of a solute is a result of advective motion (fluid motion) and diffusive…

A:

Q: Calculate the density of n-butane at 375 K and 10 bar pressure. Assume the gas fits the viral state…

A: Given following data: • Temperature (T) = 273 Kelvin • Pressure (P) = 10 bar = 10⁶ pascals •…

Q: 1. Based on the following figure, answer the following questions : (a) How many actual trays are…

A: Mc-Cabe Thiele diagram of a mixture is given.

Q: polymetric ferric sulfate in the basin at the moment of overflow.

A:

Q: Anthocyanins are being extracted from a bed of blueberries (15 cm in depth). The berries are in a…

A: Given : Depth of the bed of blueberries Length of the tray Width of the tray Velocity of the solvent…

Q: 9.08. Given the following data: 1.000 ml of NaOH« 1.117 ml HCI. The HCI is 0.4876 N. How much water…

A:

Q: Problem 1: Reynold's number a rotating brush uses a device similar to the device shown in HD Figure…

A:

Q: DIFFERENTAL EQUATION: ELEMENTARY APPLICATIONS 1. A spherical vessel, 150 cm in diameter is…

A: Given Data : Diameter of the spherical vessel (D) = 150 cm =1.5 mDepth upto which water is filled…

Q: Exercise 3. Find the distance between the settling chamber to remove dust from a gas stream. The…

A: To calculate the distance between the trays of a settling chamber to remove dust from a gas stream,…

Q: An alcohol-water solution contains 50% (volume) ethanol at 300 K. The densities of ethanol and water…

A: Given 50% by volume ethanol and 50% by volume is water Let's assume 1000 ml alcohol-water solution…

Q: 4. Find the shearing stress based on the given below: 0.3m/s 250 mm acetone 20°C, 1 atm Im/s

A: The shearing stress for the acetone is to be calculated.

Q: Consider an approximately spherical graupel particle with a radius of 2 mm. The graupel falls…

A: Given: The density of graupel The density of air The initial radius of the graupel particle The…

Q: Below is a ternary liquid phase diagram containing propionic acid and water at 70:30 mass ratio is…

A: The ternary liquid phase diagram you provided illustrates the behavior of propionic acid, water, and…

Q: A company producing detergents uses industrial minerals such as phosphate salts and silica in their…

A: Given: diameter of the clay particles=50 μm=5*10-6difference between the densjties(ρp-ρL)=2400…

Q: Draw a rough sketch of the operating and equilibrium lines and label the slopes. How many transfer…

A:

Q: QUESTION 4 A sealed container contains 0.600 moles of O2 gas and 0.300 moles of N2 gas. If the total…

A:

Basic Chemical Calculations (Process and Variables)

A basic chemical calculation involves the application of the law of chemical proportions to various reactions and material and energy balance calculations on various chemical processes. Basic chemical calculation helps students analyze various chemical processes and develop problem-solving skills. The chemical manufacturing processes are divided into unit operations involving physical changes of material and unit processes involving the chemical transformation of materials. For instance, fluid flow, heat transfer, and mass transfer are unit operations, and oxidation, reduction, and pyrolysis are unit processes.