The module MSX-83 from BP solar is used in the following configuration to make a PV array: • 4 modules in series • 2 strings (of 4 modules in series) in parallel The electric characteristics at STC are given below: |Maximum power (Pmax) = 83 W Voltage at Pmax (Vmp) = 17.1V Current at Pmax (Imp) = 4.85A What will be the electric characteristics of the PV array? Short-circuit current (Isc) = 5.27A Open-circuit voltage (Voc) = 21.2V

The module MSX-83 from BP solar is used in the following configuration to make a PV array: • 4 modules in series • 2 strings (of 4 modules in series) in parallel The electric characteristics at STC are given below: |Maximum power (Pmax) = 83 W Voltage at Pmax (Vmp) = 17.1V Current at Pmax (Imp) = 4.85A What will be the electric characteristics of the PV array? Short-circuit current (Isc) = 5.27A Open-circuit voltage (Voc) = 21.2V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the wave form across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 R 10 ΚΩ I14001 Q6. Can we operate normal PN junction diode in breakdown region for longer duration? Give reason Q7. What is the specialty of Zener diode so as we can operate it in breakdown region for longer duration? Q8. What is the difference between Zener breakdown and Avalanche breakdown? Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage in the range from 10V to 30V. Consider load resistance of 10KS. Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED? Q12. Which materials are used in manufacturing of LEDS?…
3.) An electric unit heater is to be designed with its coil made of nichrome wire, the resistivity of which is equal to 600 ohms per Cir-Mil-ft, and having a diameter of 40 mils, This electric heater is to take 1000 watts for its coil on a 220 volts DC source. (P = VI = I² R = V²/R ) Determine the length of the nichrome wire needed. (ANS. 117.33 ft )
a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R = 1092, L=20 mH, and a = 60°. Determine: i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. Vs S₁ S4 Figure $3 $₂ Lo Vo
Discuss the importance of Maximum Power Point or Ideal operation point of a PV Cell and how is it obtained.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
4- Single phase centre-tape rectifier with 100V peak secondary voltage per coil, energizing 10 Ohms and 2mH inductance with 50Hz source. The output rectified voltage drops to ...of the Vdc. *
VoO for Ma mosfet Nn Cox ( )= Jm Alv? ,Vrw=0,7V J00NA (+) VX %3D %3D a) In uhat condition does the mosfet work ?and frnd the voltage Vx= ? M1 3V b) what is the mompmum Voo voltage and why'?
how to measure ripple factor and peak input and peak output voltage for this circuits ?
An ideal single-phase source, 240 V, 50 Hz, supplies power to a load resistor R= 100 Ohm by full -wave rectifier (a) Calculate the average and rms values of the current and the power dissipation. (b) Calculate the circuit power factor and the ripple factor.
What do you mean by Ferranti effect? How does it affect voltage regulation? Which one among efficiency and voltage regulation can be negative? Give reasons?
DA shunt generator is used to charge a battery of 100 cells in series. If each cell has a terminal p.d. of 2.5V at the completion of charge and is of internal resistance 0.001 Q calcu- Cate the e.m.f. to be generated to give a charging current of 15A at the end of charge. Assume that the armature and field resistances are 0.2 2 and 200 2 respectively and the cables onnecting the generator to the battery have a resistance of 0.6 Q.
b) What are the advantages and disadvantages of solar PV cell combined connection?