, the minimum metric specification required for the bolt is

Q: Provide the sectional front view, looking at the direction X, draw the top view, and left-side view…

A: Find Sectional front view, top view side view, front view, and right side view.

Q: 10. A lending company discounts 15% simple interest per year on loans made . If a member borrows…

A:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: A cylindrical bronze sleeve (2) is held in compression against a rigid machine wall by a…

A: The steel bolt properties are  E1=200 GPaα1=11.7*10-6/C The bronze sleeve properties are  E2=105…

Q: What is the velocity of the joint at point B? a. 5in/s b. 6in/s c. 7in/s d. 8in/s

A:

Q: 2.92 For the object shown in Figure P2.92, calculate SA for neutral stability when submerged. А 80…

A: Dear Students The answer is given below

Q: 4. Hot oil (cp= 2.5 kJ/kg-K) at 125 C with a flow rate of 97 kg/min is used in a shell-and-tube heat…

A:

Q: Prob. # 3] A 0.453 kg mass is attached to a spring having static deflection of 7.87 mm. Calculate,…

A: Deflection (∆) =7mm To fund natural frequency of system

Q: 17-A28 The 2000-kg truck has rear wheel drive. The coefficient of friction between the rear tires…

A:

Q: Determine the permanent elongation of the bar after removal of the load. [Assume elastic, perfectly…

A:

Q: The lap joint is fastened with four 3/4-inch diameter rivets. a. If the allowable shearing stress of…

A:

Q: A one-shell pass and two-tube passes heat exchanger must transfer 300 kW to a solution with a…

A:

Q: Find the width of a heavy-single ply leather belt (8.75 hp/in) transmitting 11 hp at 1800 rpm motor…

A: Given, Heavy - Single ply leather belt Power, p = 11hp; Speed of the motor, N = 1800 RPM cm =0.696…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: at is the internal normal force?

A: In a beam,  The sum of all the axial force acting at a section of a beam is called as internal…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

A:

Q: Question 1. A multi degree of freedom robotic arm moves so that P travels in a circle about Point B,…

A: Tangential acceleration, at=10 mm/s2 Speed, v=att   Normal acceleration, an=v2p=at2t2pwhere…

Q: Carbon dioxide (CO₂) fills a closed, rigid tank fitted with a paddle wheel, initially at 80°F, 20…

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Rod ABC has a diameter of 30 mm at AB and diameter of 20 mm at BC. the whole rod is subjected to a…

A:

Q: We used the average sea level pressure Po What is the mass of air pressing down on the top of your…

A:

Q: 2.18 The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal…

A:

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: Estimating machine capability for your samples: Detemine the model and functioning of the system and…

A: A UTM or universal testing machine is an apparatus designed to carry out various tests by making…

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: Refer to Fig. 8-27 below. The weight of A is 50 lb; the weight of B is 80 lb. The coefficients of…

A:

Q: Determine the angular velocity of the planetary gear B. (You must provide an answer before moving on…

A: To find: Angular velocity of planetary gear B  Copyfish OCR…

Q: As shown in the figure below, a cylinder fitted with a piston is filled with 400 lb of saturated…

A: Given DataThe amount of the saturated ammonia filled in the piston is: The temperature of the…

Q: A horizontally positioned door weighing 1200 N is held in place by hinges centered at points A and B…

A: Given: The weight of door, W = -1200k

Q: 7. How many ½ inch diameter set-screws would be required to transmit 3 horsepower at a shaft speed…

A:

Q: Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O.…

A:

Q: A thermally operated contact mechanism is shown. If heated above the ambient temperature of 20°C…

A:

Q: Silver or Ag (Dr. Tree's third favorite metal) melts at 961.8°C and has a Heat of Fusion = 88 Jlgm.…

A:

Q: es the specification "8.8" in the standard designation of a bolt mean? Specify values including…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: For a No. 7 ball bearing, the New Departure Handbook states that the maximum bore should be 1.3780…

A:

Q: The denomination for a force or shrink fit in the US system is ?

A: Solution:

Q: Calculate the moment Mg of the 900-N force about the bolt at B. Simplify your work by first…

A:

Q: What is the normal reaction at B (Bv)? For items 13-20, refer to the compound beam shown. Note:…

A:

Q: A particle moves along the curve y = x - (x² / 325), where x and y are in ft. If the velocity…

A: Given, y=x-x2325vx=3ft/sax=0(as velocity remain constant)x=15ft Now,…