The measured length of two points along the ground was recorded as 550.00 m. The 50 m tape is of standard length at temperature 15 °C and a pull of 40N. During measurement, the temperature reading was 36'C and the tape was supported at both ends with an applied pull of 48N. By raising the tape, sag was also observed. The cross sectional area is 6.50 mm² and the modulus of elasticity is 200 GPa. The tape has a unit mass of 0.07 kg/m. (K=0.0000116/"C) Determine the corrected distance in meters. NOTE: Units are not required. Round-off to two decimal places.

The measured length of two points along the ground was recorded as 550.00 m. The 50 m tape is of standard length at temperature 15 °C and a pull of 40N. During measurement, the temperature reading was 36'C and the tape was supported at both ends with an applied pull of 48N. By raising the tape, sag was also observed. The cross sectional area is 6.50 mm² and the modulus of elasticity is 200 GPa. The tape has a unit mass of 0.07 kg/m. (K=0.0000116/"C) Determine the corrected distance in meters. NOTE: Units are not required. Round-off to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Between a plate and the body of a bolt or a pin, the average bearing stress is computed by dividing the transmitted force by the _______ area.
can you help me with detailed solution pls 2. A line was measured with a steel tape which was exactly 30m at 18°C and a pull of 50N and the measured length was 459.242m. Temperature during the measurement was 28°C and the pull applied was 10ON. The tape was uniformly supported during the measurement. Find the true length of the line f the cross sectional area of the tape was 0.02cm², the coefficient of expansion per °C = 0.0000117 and the modulus of elasticity = 21 x 10° N per cm².
Part A Determine average normal stress. (Figure 1) Express your answer with the appropriate units. Javg = Part B μA Submit Request Answer Value σ1,02= 20 MPa IVD ΑΣΦ11 Units vec ww Determine the principal stress. Enter your answers numerically separated by a comma. ? 80 MPa 30 MPa www MPa
A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner diameter is 0.18m. The rod is compressed axially with a load of 200kN. The modulus of elasticity and the Poisson's ratio of the rod are 200GPa and 0.3 respectively. Determine the decrease in length of rod.
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 2.35 in. to 2.56 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve - Mandrel Answers: (a) E0= in./in. (b) Ec= in/in.
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P= 1250 lb. The dimensions of the wooden specimen are t = 2.5 in. and L = 4 in.
need help asap plsss tq....
Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
A tensile test is conducted for a metal wire which has a diameter of 4.5, the maximum recorded force was 3700N. Thus, UTS point is:
Situation 8: The rigid, horizontal slab is attached to two identical copper rods. There is agap A = 0.08 mm between the middle bar, which is made of aluminum, and the slab.Neglecting the mass of the slab, the temperature in in all rods by 60°C. Use the following data: Each bronze rod Aluminum rod 22. Compute the stress in bronze rod 23. Compute the stress in aluminum rod 24. Compute the deflection on the rods Bronze A (mm²) 650 480 A Aluminum a (/°C) 18.9 x 10-6 23.1 x 10-6 Bronze 850 mm E (GPa) 83 70
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
Icles Current Attempt in Progress A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 1190 mm, b = 590 mm, c = 1.1 mm, and d = 0.8 mm. R Answer: Shear strain yy prad. %D