The maximum peak to peak value of an AM wave is 43 volts and its frequency is 25000000. The peak to peak value of the modulating signal is 21volts and its frequency is 16000. If it is transmitted through an antenna with an internal resistance of 49ohms, 5. Carrier power Pc 6. Power in side bands Psb 7. Power in upper side band Pusb wwwn 8. Total transmitted current It

The maximum peak to peak value of an AM wave is 43 volts and its frequency is 25000000. The peak to peak value of the modulating signal is 21volts and its frequency is 16000. If it is transmitted through an antenna with an internal resistance of 49ohms, 5. Carrier power Pc 6. Power in side bands Psb 7. Power in upper side band Pusb wwwn 8. Total transmitted current It

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

%VE 11₁. 1₁. H+ 1. Find the carrier frequency swing of the FM signal. 2. Determine the highest and lowest carrier frequencies. 3. Calculate the modulation index for the wave? 1- An FM modulator has a carrier frequency of 200 MHz, is frequency modulated by a sine wave signal at a frequency of (fm= 15 kHz). The resultant FM signal has a frequency deviation of (f= 45 kHz). 4. Sketch, approximately to scale, the magnitude spectrum Show all frequencies of interest. 5. Calculate the bandwidth occupied by this FM signal? - 0 ۱۱:۳۸ Untitled ||| 2- An FM modulator uses a carrier frequency of 1000 Hz and a frequency sensitivity constant Kf = 12.5 Hz/volt. The message is m(t) = 4 cos 2710 t. O the modulator output. 1. What is the modulation index? 2. Sketch the magnitude spectrum of the modulator output. Show all frequencies. 3. Is this narrow band FM? Why? •N خ 11:+V ·K मं
A carrier of 16 cos (2710't) volts is amplitude modulated by a modulating signal of 8 cos(2710³t) volts. Determine: 2. The total power and the transmitting efficiency over 50 2 load. 3. The upper and lower amplitude and frequency and the total bandwidth. 4. Plot the amplitude spectrum of this AM-DSB.
solve Q 4,5,6
In an AM modulator the message signal is m(t) = coswmit+2coswm2t, and the carrier wave is c(t) = Acosw.t. The modulation index is m = 0.5. a) Determine the amplitude of the carrier wave A. b) Determine the expression of the modulated signal with the AM modulation scheme. c) Determine the expression of the frequency spectrum of the AM modulated signal and then plot the frequency spectrum.
What is Transmission Efficiency of an AM wave? Discus the Evaluation of Modulation Index and Transmission Efficiency
Q7. Figure Q7 shows a modulated waveform v(t) in millivolts as a function of time t in nanoseconds. 1.5 1.0 0.5 - 0.0 -0.5 -1.0 -1.5 100 200 300 400 500 t/ns Figure Q7: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) Demodulation of this type of waveform is usually performed with an envelope detector. Describe the function of an envelope detector and sketch an example circuit. (g) What requirements on the values of the components of your envelope detector circuit are there for the successful demodulation of the given waveform? (h) Keeping the same carrier wave, the modulating wave in this example is substituted with a square wave of 50%…
Which of the following statement is incorrect? A. Assuming that XTAL = 10 MHz, TCNTO = 50 to generate a delay of 15 us in Normal mode. %3D Assuming that XTAL = 16 MHz, Prescalar N = 8 and OCRO= 7 to generate a square wave pulse with duty cycle 50% and frequency 1MHZ. C. Assuming that XTAL = 10 MHz, OCRO = 149 to generate a delay of 15 us in CTC mode. D. Assuming that XTAL = 8 MHz, Prescalar N = 256 and TCNTO= 131 to generate a delay of 4 ms in Normal mode. %3D
15. A 100-V carrier is modulated by a 1-kHz sine wave. Determine the sidefrequency amplitudes when m 0.75. (37.5 V) 16. A 1-MHz, 40-V peak carrier is modulated by a 5-kHz intelligence signal so that 0.7. This AM signal is fed to a 50- antenna. Calculate the power of each spectral component fed to the antenna. ( W, W) 17. Calculate the carrier and sideband power if the total transmitted power is 500 W in Problem 15. (390 W, 110 W) 18. The ac rms antenna current of an AM transmitter is 6.2 A when unmodulated and rises to 6.7 A when modulated. Calculate %m. (57.9%) 21. An AM transmitter has a 1-kW carrier and is modulated by three different sine waves having equal amplitudes. If , calculate the individual values of m and the total transmitted power. (0.462, 1.32 kW)
Find the wavelengths of (a) a 450 MHz, (b) a 650 MHz, (c) an 8 MHz, and (d) a 850 KHz signal.?
In an antenna array, the array factor depends on Tick all that apply. O Radiation pattern. O Relative excitation magnitude. Efficiency of each element O Relative excitation phase. Beamwidth. Number of elements Input resistance. O Operating frequency. O Spacing between elements O Directivity of elements
H.W A carrier signal given by 10cos27×108t volt is FM modulatedby single tone message 4cos2nx103t voltif the modulation constantis 1000 HzlVolt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulatedwave. c) Sketch the spectrum. d) Calculate sidebands carrierand total power.