The mass moment of inertia I of a disk isgiven by1Imr²where m is the mass of the disk and r is theradius. Create a graph that shows I as afunction of r for a steel disk with a densityof 7800 kg/m³. Vary the r value from 10 cmto 25 cm. Assume a thickness of 1 cm.

Solution: Mass moment of inertia of a disk I=12mv2 Density of steel=7800 kg/m3 Range of variation of…

Answered: The mass moment of inertia I of a disk…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5.) The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a specific gravity Sb =0.25, a square base of 80 mm x 80 mm and height of 15 mm. The metal has a volume of 8000 mm^3. Using a unit weight of water 9800 N/m^3 and g=9.80 m/s^2., find the mass of metal in grams. Write your answer in two decimal places. fluid mechanics
A steel rectangular block, a = 2.4cm wide and b = 1.2 cm deep, is subjected to an axial tensile load as shown in the figure. Measurements show the block to increase in length by x=7.11×10-5m (initial length=10cm) and to decrease width by 8 z = 0.533×10-5m, when P is 45 kN. Calculate the modulus of elasticity and Poisson's ratio for the material. P
Determine the mass moment of inertia of the figure shown about the x,y, and z axis. The materials weighs 60 kN/m³.
Question 9 In the figure, a 119 kg uniform log hangs by two steel wires, A and B, both of radius 1.20 mm. Initially, wire A was 2.70 m long and 2.05 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 × 1011 N/m². What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio dд/dB? (a) Number i Wire A Wire B com Units (b) Number i Units (c) Number i Units --/1
A cylinder weighing 20 pounds slides in a free pipe as shown in the figure. The clearance between the cylinder and the pipe is 0.001 in and it is filled with oil of relative gravity 0.80. If the cylinder is observed to decelerate at the rate of 2 ft/s^2 when the speed is 20 ft/s. Calculate dynamic and kinematic viscosity W = 20lb u = ? %3D %3D S oil = 0.80 p = ? %3D V = 20ft/s %D ccciinther Bripelgne epinder 5 inches
The density of a metrail is 1,750 kg/m3Required: Determine the unit weight of the material in kN/m3Use g= 9.81 m/sec^2 in your calculation.Write the answer up to two decimal places
The air resistance to the motion of a vehicle is something important that engineers investigate. As you may also know, the drag force acting on a car is determined experimentally by placing the car in a wind tunnel. For a given car, the experimental data is generally represented by a single coefficient that is called the drag coefficient. It is given by the relationship: Fa C, = where C, = drag coefficient F, = measured drag force (Ib) p = air density (slugs/ft') V = air speed inside the wind tunnel (ft/s) A = frontal area of the car (ft²) What is the appropriate unit for C, if the preceding equation is to be homogeneous in units? Show all steps of your work.
A particle travels in a straight line with constant acceleration. When s = 4 , v=5 ft/s andwhen s=8, v=7 ft/s. Determine the acceleration ft/s^2.
A skier starts from rest on the 37° slope at time t = 0 and is clocked at t = 2.35 s as he passes a speed checkpoint 15 m down the slope. Determine the coefficient of kinetic friction between the snow and the skis. Neglect wind resistance. Part 1 37° Correct Calculate the acceleration of the skier. Answer: a = 5.43 Hint eTextbook and Media m/s²
In the figure shown, originally there is a H2=9 cm manometer reading and H1=15 cm. Atmospheric pressure is 101.3 kPa. what is the absolute pressure at A (kPa)? If the absolute pressure at A is doubled, what then would be the manometer reading (cm) ?
As shown in figure, a block of mass M slides on a horizontal table on oil film of thickness h and viscosity μ. The mass m causes the movement. Derive an expression for the vis- cous force on the block when it moves at a velocity u. Also obtain an expression for the maximum speed of the block. M Oil, H U m
A piston having a cross-sectional area of 0.23 m² is located in a cylinder containing water as shown in the figure below. An open U-tube manometer is connected to the cylinder as shown. For h₁ = 63 mm and h = 132 mm what is the value of the applied force, P, acting on the piston? The weight of the piston is negligible. P= N Piston TU Water Mercury P

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The mass moment of inertia I of a disk is given by 1 I mr² where m is the mass of the disk and r is the radius. Create a graph that shows I as a function of r for a steel disk with a density of 7800 kg/m³. Vary the r value from 10 cm to 25 cm. Assume a thickness of 1 cm.