The lug nut on the free-turning wheel is to be removed using the wrench. Which is the most effective way to apply force to the wrench? Also, why is it best to keep

Q: Swivel flange center helps to permits the rod buckling due to compression or tensile shock forces.…

A: Answer: True The given statement Swivel flange center helps to permits the rod buckling due to…

Q: If I had one singular hinge joint, which total different direction could it provide a force in?

A: The hinge joint can rotate and proves zero restriction about the hinge point, thus moment reaction…

Q: 3. A hand truck is used to move an R-134a cylinder. Knowing that the combined weight of the truck…

A: The combined weight of the truck and cylinder is W= 180 lbs acting at the center of gravity G, To…

Q: Find left roller support reaction

A: Given data : Point load P=20 KN Point load Q=20 KN   Required : Left roller support reaction

Q: this beam. Select all that apply. 80 KN 20 kN/m 6 m -40 LN -40 LN from the choices below for 13 m

A:

Q: 1. Why many irregularities are there in your car tyre face? explain the concept. 2. Explain the type…

A: 1. Why many irregularities are there in your car Tyre face ?          Note :- you have posted…

Q: A quick return mechanism is shownbelow. The crank OS is driven at 2 rev/s in Counter clockwise…

A: Given: A Quick return motion mechanism

Q: 2.92 For the object shown in Figure P2.92, calculate SA for neutral stability when submerged. А 80…

A: Dear Students The answer is given below

Q: 1.5m 1.5m x A C. B 2m/2 D (0.0.3) ( / B (5, 0, 3) FAB Z W C (-5, 0, 3) FAC A (0.2.1.5) C 5m E(0. 4.…

A:

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: Once it begins to roll without slipping, what is the force of friction on the ball?

A: Given data:- Mass of the ball (m)=4.6 kg Kinetic friction coefficient =0.3 To find:-the force of…

Q: 1- Does increasing the contact angle between the belt and pulley affect the amount of friction…

A: Belt and Pulley system is used to transmit power from one shaft to another shaft. In this mechanism…

Q: Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of…

A:

Q: When the drive belt deflections in the lathe machine are less than 6 mm the tensioners are used for…

A: Answer - True

Q: The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one:…

A: That is true, as we know that the transformation from the last joint to the tool contains a rotation…

Q: Forces A, B, C and D are acting on a horizontal bar which produces a resultant of 300 lb acting 4 ft…

A:

Q: 4) Sketch the free body diagram for the motor blower assembly shown below. Show the torques at the…

A: Power of the motor, P = 1 hpspeed of the motor, N = 1800 rpmthe distance between the mount, L = 10…

Q: cylinder failed due to static load or cyclic load

A: The failure occurs in wheel cylinder due to cyclic loading.

Q: 1) (a) How many degrees of freedom does (do) the knee joint and the shoulder joint have? (b)What is…

A: Solution: (a)

Q: Draw FBD and solve for static equilibrium

A: For solution refer below images.

Q: The machine shown in the figure can be used for a tension test but not for a compression test. Why?…

A: Given: There are three gears connected in series and the middle gear is attached to the motor. And…

Q: Theories in Structural Analysis Combined stresses: tutorial question 3** The rectangular block of…

A: Given data  The vertical force = 40kN Find the largest normal stress

Q: The Moment of inertia around the hub of the circle. Angular acceleration of B. Acceleration of A.…

A:

Q: A wheel and axle transfer a force from one wheel to the axle and on to__. A. The other wheel B.…

A: The wheel is a round member which converts the rotational motion of the member into translational…

Q: Show that the same rebound can be expected for any position of knob K.

A: as earlier calculated ω2=3gLω3=3gL1-cosθ

Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…

A:

Q: Determine the moment of force F about point 0, about point A and about line OB

A: The moment about any point is the cross product of the force and position vector which is calculated…

Q: Question 4 (Type C): If a clamping force of 350 N is required at A, what is the magnitude of the…

A: F=504.7NExplanation:

Q: If the deflections of the drive belt of a lathe machine exceeds 8 mm tensioners are used for…

A: If the deflections of the drive belt of a lathe machine exceeds 8 mm tensioners are used for…

Q: (8) A 5,000-lb gearbox is provided w/ a steel eyebolt for use of moving it. What should be the size…

A:

Q: What torque does the force F produce with respect to the nut's axis when α = 46 degrees? Tips: One…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.