The LRT trolley system 10 miles long is fed by two substations that generate 600 volts and 560 volts , respectively. The resistance of the trolley wire and rail return is 0.3 ohm per mile. If the car is located 4 miles from the 600 volt station draws 200 A from the line. How much is the current supplied by each station?

Q: A 2 wire d.c distributor AB is fed from both ends at 230V. The total 1length of the distributor is…

A:

Q: How is power system protection implemented, and what are the key devices and strategies used to…

A: How is power system protection implemented and what are the key devices and strategies used to…

Q: Which among these statements is false or incorrect? A. The bigger the value of the Breaking Stress,…

A: The sag for a conductor is calculated by the formula  Sag=wl28TT=Tensile strengthsafety factor And…

Q: What are the key challenges in power transmission within a power grid?

A: Key challenges in power transmission within a power grid?

Q: Give the raceway size required for each of the following conductor combinations: 1. Five, 10 AWG,…

A: The raceway size  required for each of the following conductor combination is given as per the…

Q: How does IoT fit into the concept of the "smart grid" in energy distribution

A: We need to explain How  IoT fit into the concept of the smart grid in energy distribution.

Q: These transformers normally mounted on power poles or installed inside a large building near…

A: 1) Transformer is an electrical machine which step up step down the voltage without change in…

Q: Several factors or conditions can cause conductors to overheat, but often overlooked is the…

A: The heating is the major concern in the conduction as the temperature increases then the resistance…

Q: Explain the concept of electrical grid reliability and its importance.

A: To explain:the concept of electrical grid reliability and its importance.

Q: Define the terms "load shedding" and "voltage regulation" in the context of power systems. How do…

A: Load SheddingLoad shedding is a controlled and intentional reduction or shedding of electrical load…

Q: The power system shown in Figure Q2.2 experiences a three-phase fault at Bus 5. The fault current at…

A: The system is given asherebase MVA is 100.

Q: Question: How do the secondary voltage and current react to the different types of load and how do…

A: It is asked how in transformer the secondary voltage and current react to the different types of…

Q: What are Diagram,Construction, Operation, Advantages and Disadvantages of DC Circuit Breaker.

A: A circuit breaker is a flexible device that can be automatically operated to control and protect the…

Q: What is a circuit breaker? What is the most important parameter that helps to determine the rating…

A: A circuit breaker is a device that can detect overloads above its rating in a circuit and…

Q: Define the term "load shedding" in the context of a power system and explain its significanc

A: we have to define the term "load shedding" in the context of a power system and  we have to explain…

Q: What is load shedding, and how is it used to manage electricity demand in power systems during peak…

A: Load shedding is a controlled and temporary reduction of electricity supply to specific areas or…

Q: 500/5 A в C X R ele Va Basic Negative Phase Sequence Current Filter

A: The given circuit diagram is shown below:

Q: How does power system protection work, and what are the different protection schemes and devices…

A: Power system protection is a branch of electrical engineering that focuses on ensuring the safe and…

Q: What is electrical sub station?

A:

Q: pure dc will have ____ ripple

A: Ripple is the residual periodic variation of the DC voltage within a power supply which has been…

Q: The LRT trolley system 10 miles ling is fed by two substations that generate 600 volts and 500…

A: Total resistance of the wire = resistance per mile× length of the wire in mile. Voltage drop in line…

Q: A circuit breaker is rated as 132 KV, 4000 MVA. What will be the Asymmetrical breaking current…

A: Given- A circuit breaker 132 KV, 4000 MVA, DC  component =70%, To Find- The asymmetrical breaking…

Q: G FOTO 100 MVA 13.8 kV X₁ = 0.15 p.u. X₂ = 0.17 p.u. Xo = 0.05 p.u. AY 100 MVA A:Y 13.8:138 kV X =…

A: Given dataGenerator:Transformer :Line:Transformer :Motor:We need to calculate the value of the phase…

Q: Is there any iron lost in the short circuit test? If there is, why is it omitted

A: Yes, in short circuit test, iron losses or core losses are not absent (or zero) but they are…

Q: 2. Compare the properties of Solid insulators and liquid dielectrics? 3. Define Basic Insulation…

A: 1.A voltage multiplier circuit is used to generate high voltage DC from a low voltage AC source. The…

Q: Two persons are standing near a HV equipment and working on it, when an arc flash occurred. Person A…

A: According to the given information, person A was standing directly in front of the high voltage (HV)…

Q: Underground service conductors shall have [Fill-in-the-blank]. A)adequate mechanical strength.…

A: According to the section 230.31 Underground service conductor shall have sufficient ampacity for the…

Q: Explain the significance of power transmission and distribution in the electrical grid, and the…

A: Power transmission and distribution are crucial components of the electrical grid, playing a…

Q: What are the different types of power generation sources, and how do they impact the grid

A: we need to explain:the primary sources of energy generation in a power system and how they impact…

Q: 01: (A) It is required to generate a high D.C. voltage 40 KV using power transformer (50 KV,1 KVA).…

A: An autotransformer  has a primary winding and secondary winding which is only one single voltage…

Q: i) At the starting of the experiment with parallel operation of transformers, ______________.…

A: Given questions: At the starting of the experiment with parallel operation of transformers,…

Q: Explain the concept of electrical load shedding and its role in power system management.

A: Electrical load shedding is a controlled and temporary interruption of electricity supply to certain…

Q: How do voltage sags and surges affect electrical equipment, and what measures can be taken to…

A: Voltage sags and surges are common power quality issues that can have significant effects on…

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.