العربيهThe local friction coefficients arehigher in turbulent flow than theyare in laminar flow because ofthe intense mixing that occurs inthe turbulentWhyتحويل الصوت إلى نصمحادثةكاميراترجمة منالإنجليزية( الإنجليزيةThe local friction coefficientsare higher in turbulent flowthan they are in laminar flowbecause of the intense mixingthat occurs in the turbulentWhy...

Answered: Image /qna-images/answer/ec9cb5c0-1530-48ac-8e04-49f07e5abbf9.jpg

Answered: The local friction coefficients are…

The local friction coefficients are higher in turbulent flow than they are in laminar flow because of the intense mixing that occurs in the turbulent Why

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show that the kinetic energy of oil flowing through a pipe is 1.2961 ft-lbf/s given the folowwing: diameter of pipe = 2 in Flow rate = 40 gal/min SG = 0.90 water density = 62.3 lb/ft3
Briefly explain the shear stress and velocity profile for turbulent flow.
What are the flow Q and the velocity V when total head loss is H = 25 m?
A horizontal fan (such as that shown in example 5.24) pulls in stagnant air (ie. basically stationary air) atatmospheric pressure; the air approaches the fan outlet with speed 44 ft/sec (ie. 30 mph) and with static pressure 0.3 psi. The air flowing through the fan can be assumed to have a constant density of 2.4*10-3 slug/ft3. The air losses due to friction are 0.1 psi (or 6000 ft-lb/slug of air passing from the fan inlet to the outlet). a) Determine the shaft work in ft-lb/slug b) If the fan outlet area is 2 ft2, determine the rate of work on the air.
Hot air (43 °C) at 1 atm flows into a circular plastic duct 50 m long at a rate of 0.2 m3/s. If the friction loss, hL, in the pipe does not exceed 6 m. Determine the diameter of the duct, the velocity of the fluid, and the Reynolds number.
Air at atmospheric conditions (101.3 kPa and 20° C) enters the bottom of a 90° conical flowmeter duct at a mass flow rate of 0.4 kg/s, as shown in Fig. 4. It is able to support a centered conical body by steady annular flow around the cone. The air velocity at the upper edge of the body equals the entering velocity. Estimate the weight of the body in newtons 90° -d = 7.5 cm Fig. 4
The properties of the air in the inlet section with A1 = 0.2562 m2 in a converging-diverging channel are given as U1 = 256,2 m/s, T1 = 362 K, P1 = 136,2 kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is given by h.
Water at 15 degrees Celsius is flowing through a 2-in ID smooth pipe. The friction loss for a 100-ft section of the pipe amounts to 4.8 lbf/lbm. Determine the velocity of the flow.
Problem 5. A horizontal rough pipe with surface roughness of 1.5 × 104 m is used to transport pressurized air at a flow rate of 7 × 102 m³/s. The design guidance requires that the pressure drop must be no more than 4.2 kPa per 50 m length of the pipe. Determine the minimum diameter of the pipe
A blower supplies standard air to a plenum that feeds twohorizontal square sheet-metal ducts with sharp-edged entrances.One duct is 100 ft long, with a cross-section 6 in by6 in. The second duct is 200 ft long. Each duct exhausts tothe atmosphere. When the plenum pressure is 5.0 lbf/ft2(gage) the volume flow in the longer duct is three times theflow in the shorter duct. Estimate both volume flows andthe cross-section size of the longer duct.