The load across a 50.0-V battery consists ofa series combination of two lamps with resistances of 125 $2 Dand 225 Q. a. Find the total resistance of the circuit. b. Find the current in the circuit. 14. c. Find the potential difference across the 125-2 Olamp.

Q: Please answer in typing format solution

A: Step 1: Given peak voltage of input on the primary side of transformer Vp= 190V. When it is…

Q: The figure4 shows the relation between resistance and temperature for the thermistor.…

A:

Q: (e) Given the Wheatstone bridge of figure I with the galvanometer reading indicating the variable…

A:

Q: A potential difference across 24 2 resistor is 12 V. What is the current through the resistor?

A: Potential difference V=12 V. Resistance R=24 Ω.

Q: hich of the following statements is TRUE about the ement shown? -7 A It absorbs 1.4 W of power. It…

A: As  per our guidelines we are supposed to do the 1st question only.  So kindly repost the remaining…

Q: Figure for numbers 1 to 7. Determine the voltage and current of the diode in a) the 1st…

A:

Q: own below, pss the load 120 V RL Vi 2 kN -100 V 3 k2

A: Here i have solved this with the information given.

Q: Ohm is the unit of resistance and it is a unit. ........ Derivative basic complex

A:

Q: Figure Q1(a) shows a circuit using germanium and silicon diode. Based on the figure calculate the…

A: Explanation: The forward voltage of silicon diode is 0.7 volt and the forward voltage of germanium…

Q: Which of the following is the element formed by pressing two metals with different expansion…

A: Bimetal element is formed by pressing two metals with different expansion coefficients

Q: Determine whether the diode is conducting or not. Assume thatthe diode is an ideal diode.

A: Concept , References and Examples: Examples-1Examples-2  Thank you

Q: In a semiconductor crystal, the atoms are held together by O a. covalent bonding b. interaction of…

A:

Q: Vww る2e 200 (4 +) 5A

A: As given in the circuit apply KCL at node at 6 ohm V-2010+V12+V6-5=0V110+112+16-2-5=0V0.35=7V=20v

Q: Ferromagnetic materials have this characteristic.    A. A relative permeability slightly less than…

A: We are asked to identify characteristics of ferromagnetic materials from the given options.

Q: b. When the input is AC 110V @60Hz, Voltage output = 20V, Voltage ripple = 2V, and the maximum…

A:

Q: 1. Using first approximation, find the voltages across resistance. 2. Using second approximation,…

A:

Q: For the circuit shown below if Vi is reduced to 100 mV, the voltage VL = V₁-300 V 2092 100 k SKO VL…

A: Note : As per our guidelines we are supposed to answer one question only. So please post remaining…

Q: +5 V +5 v 2.5 kN 3 2.5 kN 2.5 kN (a) (b) (c)

A:

Q: Find power supplied to all of the diodes. D2 Si D3 R1 D1 5002 2V GaAs R2 D4 V1 1k2 Si 7V

A: Considering ideal diodes, the diode D1, D3 and D4 are forward biased and the diode D2 is reversed…

Q: A carbon brush used to conduct current from the commutator of a DC generator has a length of 4 in.…

A: Find the cross sectional area of carbon brush. If current flow = 400 A Voltage not exceed = 2V…

Q: Figure 3 + 6 V 10 kM 20 kn 20 kn

A: To find the output voltage of a circuit that contains a diode, it is important to find the on/off…

Q: A copper wire has a resistance of 2.4 ohms at 20-deg. Find its resistance at 75-deg. Resistance…

A: In this question we need to find a resistance of wire at 75°C

Q: 1- If we use 5000 μF, we can get a very low ripple voltage. But this is so bad and this a…

A: Ripple voltage is the amount of AC voltage appearing on a DC voltage. for the ripple voltage the…

Q: Q3: Determine the currents I1, I2, and ID2 for the network of figure. the diodes are assumed to be…

A: We need to find out the current for given circuit.

Q: A RTD made up of platinum has a=0.00385 and has a initial resistance of 220. Find the value of…

A:

Q: Problem 1 10 K D3 The diodes in the circuit are Silicon with forward voltage of 0.7 V. Fill up the…

A: Brief description: In the above question they want to know the value of current and voltages across…

Q: Describe the traces you would see on an oscilloscope monitoring voltage changes across a resistance…

A:

Q: ii) Draw the cross-section of this p-n junction and show the depletion region and the corresponding…

A:

Q: The diodes in the circuit given below are identical and each one is ideal. Accordingly, determine…

A: For first circuit shown below:

Q: Notes on the verification of ohm's law by voltage method?

A: Current" typically refers to the flow of electric charge in a circuit. It is measured in Amperes (A)…

Q: R I1 Given (ideal diode): a. Vo b. I1 ID1 ID2 0.33k2 E D1 D2 Vo 10V c. ID1 d. ID2

A:

Q: Which of the following is NOT a variable in voltametric methods? A. How the current is applied B.…

A: In this question we need to choose a option which is NOT a variable in voltametric methods.

Q: Q2/ For the current shown in the figure below, find the charge waveform and then find the value of…

A: The solution is given below

Q: If V1 = 17 V, V2 = -7 V, R1 = 1.2 kOhm, R2 = 4.7 kOhm, R3 = 2.4 kOhm, and all diodes are silicon for…

A:

Q: Determine the current through R1. Use practical diode model.

A:

Q: resistance and resistivity as level assignment Investigation resistance and resistivity wiht graph

A: Any practical electrical circuit has some resistance in the wires which carry the current. Also, the…

Q: Given the following circuit in Figure 1, determine whether the Diode is ww 5K2 conducting or not.…

A: Given circuit is =

Q: R2 D1 1800 D2 V1 E12 V R1 D3 R3 2000 1500

A:

Q: For the circuit shown fill in the table the missing parameters. In this part use the constant…

A: We are given a circuit shown below: Given that: R1=4 kΩ; R2=20 kΩ; R3=9 kΩ We have to find the…

Q: Plz answer correctly ....

A: Step 1:Step 2:

Current Division Method

The generalized current divider formula is given by the following relation below,