The lift is holding a 190 lb welght as shown. Calculate the reaction force components reaction moments at polnt D? Ignore the radius of the frictionless pulleys. Dimenslons: a= 3 ft b=7 ft c= 4 ft d= 6 In e = 4 ft a = 45 8= 30

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: As asked only the first three are solved. φ(x,y)=sinxAx2e-y+Bey

Q: A closed piston-cylinder system consists of 3.0 moles of monatomic gas, initially at temperature…

A:

Q: 290 J of energy is transferred to a system consisting of 2.0 moles of an ideal gas. If the volume of…

A:

Q: y

A:

Q: Go Cylinder A - Steel |Cylinder B -Aluminium 350 mm 500 mm IX

A: Given,  composite rod  da= 40  mm , la = 350 mm db= 50 mm , lb = 500 mm

Q: Determine the force in members BC, FC, and FE and state if the members are in tension or…

A: from the FBD,

Q: Steam is used in an ideal combined reheat and regenerative system as shown in figure A (turbine and…

A:

Q: The thermal conductivity of a sheet of rigid, extruded insulation is reported to be k = 0.029 W/m-K.…

A:

Q: 4.18 What is the composition, in atom percent, of an alloy that contains 44.5 lbm of Ag, 83.7 lb,m…

A: Given data:         mass of Ag= MAG= 44.5 lbm         mass of Au= MAU = 83.7 lbm         mass of Cu…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: *2-72. Two forces F₁ and F2 act on the screw eye. If the resultant force FR has a magnitude of 150…

A: Two forces F1 and F2 act on the screw eye.If the resultant force FR has a magnitude of 150 lb and…

Q: 1 Legs of a pneumatic system are generally equipped with and work stations receive air which meets…

A: This question is based on the concept of legs of pneumatic system and SUS.

Q: 5) 1000 kg of potatoes are processed to obtain french fries. Raw potatoes are washed, peeled, cut…

A: Given: (a) The french fries are made from potatoes which can be shown by following flow chart.

Q: QUESTION 2 The steam cycle shown in the figure operates between a boiler pressure P2-P3-5 MPa and a…

A:

Q: Using method of joints, determine the force in each member of the truss shown. indicate whether the…

A:

Q: te the force in each member of mber is in tension or compression.

A:

Q: 4 2, www www 3 al R.

A: For solution refer below images.

Q: THE SYSTEM SHOWN BELOW IS IN EQUILIBRIUM IF THE WEIGHT OF B IS 48 NEWTON CALCULATE THE WEIGHT OF A,…

A:

Q: Consider a Carnot vapor refrigeration cycle with Refrigerant 134a as the working fluid. The cycle…

A: Given:Cold region temperature, TC=40oFThe ambinet temperature, TH=90oFFind:Coefficient of…

Q: 3. In the figure below two equal forces are applied to the tap wrench a distance d from the center…

A:

Q: Answer D

A:

Q: As shown in figure 3, water (kinematic viscosity of water v =10 m's) flows out of a reservoir into a…

A:

Q: Instructions: Identify the talking components by choosing the most appropriate answer from the…

A: To determine: I directly determine what the speed of a hydraulic actuator is going to be. What am…

Q: The emissivity of iron is approximately 0.25. If an iron cube (with a side length of 0.5 m) is…

A: This question is related to heat transfer. heat transfer is due to temperature differences. the mode…

Q: 7. The relative humidity on a 90°F day is 30 per cent. a. How many pounds of water vapor are in a…

A:

Q: In (Figure 1), the man has a mass of 75 kg and the crate has a mass of 130 kg. The coefficient of…

A:

Q: An 02-series single-row deep-groove ball bearing with a 50-mm bore is loaded with a 9-kN axial load…

A:

Q: Determine P and RA

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: Your professor at HTU asked you to explain Archimedes topic to your classmates at one of the classes…

A:

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: 7. Consider a LiBr machine operating according to the following schematics: GENERATOR HIGH…

A: Given:

Q: The 9 lb particle is subjected to the action of its weight and forces F₁ = {2i + 6j - 2tk} lb, F₂ =…

A: Given : F1=(2i+6j-2tk) lbF2=-(t2i-4tj-1k) lbF3=-(-2ti) lb Concept used : The equilibrium condition…

Q: 5275 is a commonly used grade of steel For this grade, the ultimate tensile strength fy=? Select…

A: Answer For First:- According to standard for mild steel code S275 Composition: Carbon 0.25%…

Q: m = 0.350 kg. (c) Is the original energy in the spring or in the cord? (d) Explain your answer to…

A: For the option e and f and g  The solution is ttached in step 2 below

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: Situation #5: The body rotates according to the relation a = 4t, where a is in rads/s and t in sec.…

A: dw/dt = alpha it can be integrated to get the expression of angular velocity and this can be further…

Q: answer 38,39,40

A:

Q: 3. Find the absolute pressure in kPa at a depth of 10 m below the free surface of Oil of sp. gr.…

A:

Q: 76. The air inlet mass flow rate mi can be determined from a. pilAV]I b. [AV]1/vI both of the above.…

A: P1=14.7psi T1=80 F V=1000 cfm P2=100psi T2=400 F