The length of the connecting rod of a gas engine is 400 mm and its centre of gravity lies at 120 mm from the crankpin centre. The rod has a mass of 80 Kg and a radius of gyration of 182 mm about an axis through the centre of mass. The stroke of piston is 225 mm and the crank speed is 300 rpm. Determine the inertia force on the crankshaft when the crank has turned 30 ° from the inner dead centre.

The length of the connecting rod of a gas engine is 400 mm and its centre of gravity lies at 120 mm from the crankpin centre. The rod has a mass of 80 Kg and a radius of gyration of 182 mm about an axis through the centre of mass. The stroke of piston is 225 mm and the crank speed is 300 rpm. Determine the inertia force on the crankshaft when the crank has turned 30 ° from the inner dead centre.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

THE WEIGHT OF THE UNBALANCED WHEEL IS 200 KG AND IT HS A RADIUS OF GYRATION ABOUT ITS MASS CENTER, G, OF 0.3 METERS. AT THE INSTANT SHOWN IT IS ROTATING AT 6 RAD/SIN A CLOCKWISE DIRECTION. FIND THE FORCES BETWEEN AT THE PIVOT POINT C. Please include a Free Body Diagram
he assembly consists of a disk having a mass of 5 kg and slender rods ABand DC which have a mass of 2 kg/m. If L = 0.6 m, determine the moment of inertia and radius of gyration of the assembly about an axis perpendicular to the page and passing through point O. Also, find the position of the center of mass Gin relation to O. Please explain steps
The rod AB is non-uniform with a radius of gyration of 4.00 ft with respect to a horizontal axis through the center of mass G. It weighs 161 lb. At the moment shown the rod has a counterclockwise angular velocity of 3.00 rad/sec, and the spring is compressed by 2.00 ft. Calculate the force constant of the spring that will reduce the angular velocity of the rod to 1.50 rad/sec when it reaches the horizontal position. Assume the blocks A and B are weightless.
The centroidal mass moment of inertia ofthe pulley assembly is 20 ft-lb-s2. Determine (a) the tension in the cordsupporting 161-lb block , (b)the tension supporting the 322-lb block, and (c) the angularacceleration of the pulley system .Hint: Determine first the direction ofmotion, i.e. will block A move up ordown?
Determine the rotational inertia of the device shown below. R = 0.50 m, r = 0.2 m, the mass of the box is 30 kg. When Fapp= 176 N, the box has an upward acceleration of 0.8 m/s2. Use g = 9.8 N/kg.
The accelerating torque increases the speed of a flywheel from x rpm to y rpm in 15 seconds. Find 1. The accelerating torque produced during the above period. 2. Increase in the kinetic energy of the flywheel 3. Change in the angular momentum of the flywheel. 4. Number of revolutions made by the flywheel during this period. 5. Find the braking torque required to stop the flywheel completely. Assume suitable mass and radius of gyration. Also assume suitable values for rpm x and y above.
4. In order to determine the mass moment of inertia of a 4-foot diameter flywheel, the flywheel is tested\twice with different deadweight. In the first test a weight of 20 lb is attached by cord and observed to fall 10 ft in 4.6 seconds. In the second test a weight of 40 lb falls 10 ft in 3.1 seconds. Assuming that the torque due to bearing friction is constant, determine mass moment of inertia of the flywheel. Your solution must include W supporting FBDS.
Edit question Calculate the radius of gyration for the system of two tubes and a seat that form a swing with respect to the axis A shown in the figure. The dimensions of this system are shown in the figure below.The tubes have a mass of 19 kg/m. This means that each meter of tube has a mass of 19. Tubes can be thought of as slender rods.The seat has a mass of 23 kg and can be considered as a thin plate. Note that several views of the swing are offered so that you can better understand which is the reference axis A and the necessary dimensions. As you solve the problem, take into account that you are going to fill a table with the following format. It must be filled with the corresponding units.
Answer within the day with written solutions please!
Consider a wheel of radius r = 0.27 m, with six spokes (or three rods of length equal to the diameter of the wheel). The total mass of the wheel is 2.5 kg and 53% of the mass is evenly distributed on the circumference while the rest is evenly distributed on the spokes. Calculate the moment of inertia.
Parvinbhai