The LED in Fig.P5 requires 30 mA to emit a sufficient level of light. For the following circuit values, determine the amplitude of the square-wave input voltage necessary to make sure that the transistor saturates. Use 110% of the minimum value of base current as a safety margin to ensure saturation. Vcc=9 V, VCE(sat) = 0, Rc=270 2, RB= 3.3 K 2, and Bpc= 50. +Vcc Rc ON ON RB Vin 1s OFF

The LED in Fig.P5 requires 30 mA to emit a sufficient level of light. For the following circuit values, determine the amplitude of the square-wave input voltage necessary to make sure that the transistor saturates. Use 110% of the minimum value of base current as a safety margin to ensure saturation. Vcc=9 V, VCE(sat) = 0, Rc=270 2, RB= 3.3 K 2, and Bpc= 50. +Vcc Rc ON ON RB Vin 1s OFF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 5
1- a. For the circuits given below calculate the currents through the zener diode (V5.1V) and the current through the Si-diode. 1k Ohm 1k Ohm -10V 1k Ohm 12V b. The emitter of an NPN type BJT is connected to ground. Its base is connected to a 5V supply with a 10K resistor. Its collector is connected to the same supply with a 6K resistor. Calculate the range of ß such that the transistor is not saturated.
Draw the n-p-n silicon bipolar junction transistor at zero bias and also in forward active mode with an aid of the energy band diagram. Please ensure to draw with careful detail, reflecting the doping density in each region.
At high levels of gate current, the characteristics of an SCR approach those of what semiconductor device? a. MOSFET b. BJT c. JFET d. Diode
Choose whether the followings are True or False. 1. The MOSFET has 2 terminals Drain and Source. 2. An E-MOSFET operates in the depletion mode. 3. The LED emits light when reverse biased. 4. In the n-channel E-MOSFET, VGs(th) has a positive value. 5. A diode conducts current when forward biased and blocks current when reverse biased 6. An n-channel D-MOSFET with a positive Vcs is operating in the enhancement mode. 7. The varactor diode acts as a variable capacitor under forward bias conditions. 8. Once a BJT transistor is in the saturation, a further increase in base current will cause the collector current to increase. 9. In a given BJT transistor amplifier, Rc=2.2KQ and r'=20 Q then the voltage gain is equal to 110. 10. Voltage Amplification Av in a BJT is the output voltage divided by the input current
The operating point of the npn transistor is defined by a couple of values: lç and Ver. Select one: O True O False
For the JFET with maximum drain current 9mA, drain current 2.5mA at gate to source voltage 4V. Calculate the pinch off Voltage.
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
A platinum RTD PT100 measures 100 Q at 0 °C and 139.1 Q at 100 °C. Calculate temperature in °C if Temperature Coefficient of RTD PT100 is given as 0.0066 and resistance is 105.2(0). O 7.16 O 7.88 O 10.91 O 8.04
The main types of field effect transistor are JFET and MOSFET b. UJT and FET O C. BJT and FET O d. None of the above
The shown equivalent circuit is valid for L BJT PNP MOSFET MOSFET IGBT Bipolar transistor Diode