The lawn sprinkler consists of four arms that rotate in the horizontal plane. The diameter of each nozzle is 8 mm, and the water issupplied through the hose at 0.009 m /s and is ejected through the fournozzles into the atmosphere.300 mm30Part ADetermine the constant angular velocity of the arms. Neglect friction at the vertical axis.Express your answer using three significant figures.

Given data Discharge Diameter Angle To find Angular velocity

The lawn sprinkler consists of four arms that rotate in the horizontal plane. The diameter of each nozzle is 8 mm and the water is supplied through the hose at 0.009 m /s and is ejected through the four 300 mm nozzles into the atmosphere. Part A Determine the constant angular velocity of the arms. Neglect friction at the vertical axis. Express your answer using three significant figures.

The lawn sprinkler consists of four arms that rotate in the horizontal plane. The diameter of each nozzle is 8 mm and the water is supplied through the hose at 0.009 m /s and is ejected through the four 300 mm nozzles into the atmosphere. Part A Determine the constant angular velocity of the arms. Neglect friction at the vertical axis. Express your answer using three significant figures.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Plzzzz
A fluid of specific gravity 0.8 and dynamic viscosity 15 x 10-4 Pa.s is flowing in a 15 mm diameter straight galvanized iron pipe (e = 0.3 mm, C = 130) of length 160 m. The flow velocity is 0.163 m/s. Calculate the friction head loss using Darcy-Weisbach and Hazen-Williams formulas.
Show your solutions.
If the flow between the two reservoirs is 3 L/s, calculate the difference in elevation between the water surface. Both pipes are made of stainless steel. Use a value of 1 x 10-6 m²/s for the kinematic viscosity of water. D = 50 mm L = 6 m D = 25 mm L = 6 m 2
Problem 2: Consider the nozzle, below, for which the cross sectional area changes linearly from the base to the tip. Water flows through this nozzle at a constant discharge rate of 0.1 m³/s. What is the A) mean fluid velocity ta point that is 12 cm away from the outlet, and B) the fluid acceleration at a point that is 12 cm away from the outlet? Your solution must include assumptions as well as a sketch of the control volume with open and closed control surfaces indicated along with area vectors for the open control surfaces. 9-cm diameter 36 cm- 3-cm diameter
ire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X= 16)Calculate the following: a) How high the water can reach if the nozzle is aimed vertically? b) What is the pressure inside the hose? c) How much extra force will be created at the reducer due to velocity change?
Subject: Hydraulics What size of brass pipe would be required to carry standard gasoline at 80 degree Fahrenheit at a velocity of 10 ft. per second with a loss of head of 15 ft. per 100 ft?
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
A 200 m of rubber cotton lined hose having a diameter of 75 mm is attached to a hydrant at which pressure is 420 kPa during the flow. Assume the hose to be horizontal and f = 0.024 29. At what rate will the water be discharged trough the rubber cotton lined hose 30. If a 25 mm diameter nozzle is attached to the hose, what would be the expected head lost if a pressure of 500 kPa in the hydrant is maintained? Use Cv = C = 0.95 31. What is the discharge may be expected if the 25 mm nozzle is attached to the hose?
A 122-mm-diameter pipe enlarges to a 148-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 293.454 kg/m3, and the velocity is 23 m/s; at section 2 of the larger pipe, the velocity is 15 m/s. Find the unit weight (in kN/m3) of the gas at section 2. Round off to three decimal places.
Use 4 decimal places in all the computations.
300 mmg 100 mmø H2O, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss.