The lapbelt assembly is to be subjected to a force of 800N.800 N45mmSIMI NWhat is the required lap length d if the glue can sustain an allowable shear stress of0.74 MPa?

Given data, Force = 800N Allowable shear stress = 0.74MPa To find the required lap length d1.

Answered: The lapbelt assembly is to be subjected…

The lapbelt assembly is to be subjected to a force of 800 N. 800 N 5 mm SO0 N What is the required lap length d if the glue can sustain an allowable shear stress of 0.74 MPa?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Related questions

Q: P4: Two wooden boards are joined by cutting and gluing them together along the plane shown in the…

A: (a) If α=20° then, θ=90°-20°=70° The normal stress is calculated as,…

Q: SW The composite bar shown in Fig. P-273 is firmly attached to unyielding supports. An axial force P…

A: Draw the figure Let RA be the reaction at A NAB=RANBC=RA-P

Q: Problem # 4: The tank with cross-section shown is fabricated from steel plate. Determine the minimum…

A: Stress = 45 MPa Internal pressure = 1.5 Mpa cross section area of plate = 800 x 180 mm Tickness t=…

Q: A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working…

A: Given: The tensile working stresses for the plywood is 1200 psi. The tensile working stress for the…

Q: A nylon thread is to be subjected to a 10-N tension. Knowing that E = 3.2 GPa, that the maximum…

Q: Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads…

A: Est=200GPa Eal=70GPa Ebr=83GPa Overall deformation= 3mm

Q: Required information A square yellow-brass bar must not stretch more than 105 GPa and that the…

Q: A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the…

A: Take diameter of threaded portion≈unthreaded portionso,Stress=PArea

Q: A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also subjected…

A: A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also…

Q: In the connection shown, 1/4-in. side and end fillet welds are used to connect the 3-in.-by-1 in.…

Q: For the section shown, if a = 200 mm, b = 25 mm, shear flow between the flange and the web is 120…

A: Asked: To determine the spacing of nails for the given cross-section. Given: Width of the flange…

Q: Question 1: The rubber band given below is subjected to the following tensile loading. Calculate the…

A: Allowable tensile strength of rubber, Allowable shear strength of steel, Tensile force, Width of…

Q: Determine if w12x14 (A36) section is Compact, Non-Compact or slender. Show neat handwriting and…

A: The given data is shown below: W12×14A36 steel

Q: The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm ameter…

A: Calculation of modulus of elasticity: Modulus of elasticity is defined as the ratio of stress and…

Q: Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below.…

Q: The composite bar, firmly attached to unyielding supports, is initially stress free. What maximum…

Q: 2. A column HP 14 x 102 of A572 Gr. 55 steel has a length of 15 ft is fixed at both ends. Compute…

Q: The composite bar shown in Fig. P-273 is firmly attached to unyielding supports. An axial force P =…

A: The given data is as follows: Axial force, P=50 kipsTempertaure at which force is…

Q: Question. Two plates each of 50 mm x 500 mm section are glued together along the length to form a…

A: Given data- Plate dimensions- 50 mm×500 mm, Shear force F=1000 N, To Find- The value of the maximum…

Q: The nominal strength for block shear in LRFD is given by; Rn = 0.6FAny+FuAnt %3D 0.6FyAgy+FuAnt What…

A: We have to determine that which of the given option is correct as per asked in the question that…

Q: Calculate the steel ratio that will produce a tension-controlled failure if compressive strength f’c…

A: Given: f'c=28MPafy=350MPa As we are considering tensioned controlled failure, as per the…

Q: f1.75 in. 5.75 in. A joint is made by gluing two plywood gussets of thickness t to wood boards. The…

A: Consider the loading diagram : Load acting on boardP=rbd x Abd = 700 x 5.75 x 1.75P=7043.75 lb

Q: A beam is made of four planks glued together. Knowing that the vertical shear in the beam is V = 500…

Q: Determine if w10x12 (A242) section is Compact, Non-Compact or slender. Show neat handwriting and…

Q: A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied…

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 350 MPa, and at compression Suc…

A: The factor of safety is defined as the ratio between the maximum and ultimate stress of the material…

Q: This is the corresponding tensile stress (MPa) at the minimum strain (as allowed by NSCP2015) of…

Q: What is the magnitude of the compressive force on the left plumb in kN? F1 the steel and the left…

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

Q: 2. If maximum tensile stress in the hanger is 140 MPa. Find allowable W. 3. If W is 60 kN, find the…

Q: 4. The two pieces of wood, 2 in. by 4 in., are glued together along the 400 joint shown in Figure 4.…

A: Shear stress Shear stress is a force that tends to distort a material by allowing it to slide along…

Q: Determine if W44x285 (A992) section is Compact, Non-Compact or Slender. Show neat handwriting and…

Q: 5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial…

A: Given data

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 25 kips, w…

Q: A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working…

A: It is required to determine the applied load on the wood board. P=σboard×Aboard=700 lbin2×5.75…

Q: Two pieces of wood, 60 mm by 120 mm each are glued together along the 40° joint. The permissible…

Concept explainers

Planar Stresses

Question

The lapbelt assembly is to be subjected to a force of 800N.
800 N
45mm
SIMI N
What is the required lap length d if the glue can sustain an allowable shear stress of
0.74 MPa?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Regular low-alloy steel has an allowable shearing stress of approximately 20.0 ksi (Fv = 20.0 ksi). The beam shown has an unusual loading pattern that will cause very high shearing forces. If this beam is a W30 X 173, will it be adequate in shear?
PLEASE ANSWER THIS QUESTION ASAP!!!
Required information A square yellow-brass bar must not stretch more than 2.4 mm when it is subjected to a tensile load of 34 kN. Given: E= 105 GPa and that the allowable tensile strength is 104 MPa, determine (a) The allowable side length of the cross-section (b) is the allowable value a maximum or a minimum? Why? (c) The allowable length of the bar (d) is the allowable length a maximum or a minimum? (a&b) The allowable side length, for the square cross section, is given as [ (mm) and the value is a (Click to select)
In the connection shown, 1/4-in. side and end fillet welds are used to connect the 3-in.-by-1 in. tension member to the plate. The applied load is 60,000 lb. Find the required dimension L. The steel is ASTM A36 and the electrode used is an E70. - Fillet welds L 3" Activate Windows Go to Settings to activate Wir TABLE 19.2 Allowable stresses in ksi (MPa) 12: 12/1 DELL end F12 insert prt sc F10 home F11 F6 F8 F9 F3
2. A column HP 14 x 102 of A572 Gr. 55 steel has a length of 15 ft is fixed at both ends. Compute the design compressive strength for LRFD and the allowable compressive strength for ASD. (Steel section properties are provided in the next page) ASTM Designation A572 Gr. 42 Gr. 50 Gr. 55 Gr. 60⁰ Gr. 65⁰ Yield Stress (ksi) 42 50 55 60 65 Fu Tensile Stressa (ksi) 60 65 70 75 80
A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate is 800 mm² and the yield strength of the steel is 260 MPa. The ultimate shear strength of the bolts is 570 MPa. A factor of safety of 1.67 with respect to yield is required for the plate. A factor of safety of 4.0 with respect to the ultimate shear strength is required for the bolts. Determine the minimum bolt diameter required to develop the full strength of the plate. Note: consider only the gross cross-sectional area of the plate-not the net area. Support Plate ↓ P
Determine the load capacity of the angle ASD. USE NSCP 2015.
Please kindly give me a,b,c and d answers..help me. Urgent Thank you
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.
SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten