The L6 x 4 x 1/2single angle shown has one line of 5/8 in bolts in each leg as shown. The bolts are spaced at 4 in in each line as shown (staggered at 2 in with respect to each other). Determine the net area (An)

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

A:

Q: snip

A: Calculate the gross area due to yielding. Ag=bt     =5×12     =2.5 in2 Calculate the nominal…

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

A:

Q: Draw and label the different types of trusses according to their classifications as to Simple,…

A: A simple definition of Truss would be as:- A truss is an assembly of members connected by nodes that…

Q: Calculate the shear stress that will need to be developed in the 1 inch diameter bolts, it the…

A:

Q: A double angle shape (L5 x 3 x 5/16) is shown below. The steel is A36 and the holes are for ½ in…

A:

Q: 14- The maximum number of bolts that can be accommodated in one row is Boş bırak Карat

A: 3 bolts

Q: The Plate shown in the fIgure has thickness of 12 mm. Diameter od bolts is 16 mm. A 36 steel is used…

A: Step 1

Q: The bolted connection shown in Figures is connected with 3/4-in-diameter bolts in standard holes.…

A: To find = Available tensile strength of plates

Q: Compute the net area of each of the given members

A: Given data in question  Plate dimensions  Bolt diameter  Staggered bolting To find out  Net area of…

Q: The tension member is a PL.3 x 5% of A242 steel. It is connected to a 3-in. thick gusset plate, also…

A: PL 3/8 x 5 1/2 A242 steel3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch diameter

Q: A Channel section is connected to a 10mm gusset plate with 20mm- diameter bolts as shown in the…

A:

Q: 3 in 3 in 8 in |2 in |14 in - PL 1 x 8 The holes are for 3/4 -in Ø bolts

A: The net area at a section is equal to the minus of the gross area of the holes deduction at that…

Q: 2. Compute for the net area of the shape shown. (Note: Bolts are going through different portions of…

A: The section is provided above. It is w 10x19 section. Also 2 M20 bolts are provided in top and…

Q: 3. Determine the gross and net areas for a 6×5/8 in. plate with a single line of standard holes for…

A: Length of plate(L)=6in Thickness of plate (t)=5/8 in  To find gross and net area

Q: 9.4 An L 8 x 4 x ½ has staggered holes for %-in. diameter bolts, as shown in Figure P9.4. Determine…

A:

Q: Determine the design tensıle strength (LRFD) of an ASTM A992 W8x24 with four lines of 4-in. diameter…

A: Tensile strength is the dimension of the amount of force acting on a particle to pull.  LFRD is to…

Q: 3. A Channel section is connected to a 10mm gusset plate with 20mm- diameter bolts as shown in the…

A:

Q: 5. Analysis of Tension Members Compute the net area of an L6 x 3 ½ x 3/8 with two lines of 3/4"…

A: Step 1: Calculate the Gross Area of the Angle Given dimensions are L6×321​×83​, where: 6 inches is…

Q: The  L7 x 4 x 1/2  single angle has two lines of bolts in the long leg as shown (See Figure). The U…

A: The distance from the centroid of the connected area to the plane of the connection, x=0.910 in The…

Q: An air chamber is held together by bolts. d = 20 cm, D = 40 cm. A-A: 20 bolts, Drolt = 2.5 cm. %3D…

A: Given : If 2.5cm of 20 bolts are able to hold at A-A. D=40cm, d=20cm,  D=2d

Q: a) Determine the net area to satisfy block shear check for the plate shown below: PL 4X10 3"8 bolts…

A:

Q: Calculate the minimum girder width to fit the longitudinal bars shown that have center-to-center…

A: Given data: Total depth of the beam, D=20 in Diameter of main reinforcing bar,d=98=1.125 in Center…

Q: 4. Determine the LRFD design strength and the ASD allowable strength of sections given. Neglect…

A: Given, Section = L7×4×12 Hence, t=0.5 inch A36 steel Diameter of the bolt=12 inch Diameter of the…