The instruction MOV AX, 6543 is bytes long.

Q: determine the time taken to execute the instruction if the clock frequency of 8085 is 10MHz. Mvi…

A: In 1977, Intel designed an 8- bit microprocessor by using NM technology, which is called 8085…

Q: How many bits is the OPCODE and what is the assembly language mneumonic for each of the following…

A: Answer: Hexadecimal Bits Mnemonics Explanation 02 000 0010 STX Start of text 08 000 1000 BS…

Q: The org is an assembler pseudo instruction. Select one: True O False

A: An assembler is a program that takes basic computer instructions and converts them into a pattern of…

Q: THE MACHINE CODE OF THE FOLLOWING INSTRUCTION IS MOV (BP),AX

A: The correct answer is 8B4600     Explanation - The machine code for MOV [BP], AX is 0101 0110 0000…

Q: Convert the given 6809 instruction to the machine ca ORB „U EA 84 FA 10 C2 CA CO EA C4 None of the…

A: 1)  FA 10 C2

Q: What is the MIPS machine language code for the following instruction? Write opcode, rs, rt, rd,…

A: The opcodes in MIPS machine language are pre determined and can be easily converted into decimal…

Q: Given the machine code, identify the instruction line or command line. Use CAPITAL LETTERS . No…

A: SUMMARY: -Hence, we discussed all the points.

Q: Write the execute cycle of the instruction "ADD E" in Register Transfer Notation.

A: write the Execute cycle of the instruction ADD E in register Transfer notation. Answer Execute…

Q: The execution cycle of an instruction can be described using Register Transfer Notation by writing…

A: Intro The instruction execution cycle comprises the following steps: Fetch Decode Execute Store The…

Q: Translate the following program to hex and binary, given that the first instruction is at address…

A: 0040004C 0     ==> 8421   ==> 0000 0     ==> 8421   ==> 0000 4     ==> 8421   ==>…

Q: MOV CL,[237A H] is a valid instruction. Select one: True False

A: Required:   MOV CL,[237A H] is a valid instruction. Select one: True False

Q: Translate the following C-code into a set of RISC-V instructions. Annotate the purpose of each…

A: lw t0, 5    // assigning variable1 with value 5 lw t1, 0   // assigning variable2 with value 0 loop:…

Q: Select an instruction that tests bit position 8 of register CH. Select the correct response: None of…

A: The CH-lower and higher halves 16-bit data register and can be used as 8-bit data register.

Q: Determine the value after the instruction (signed division). AX = 0020H DL = FCH IDIV DL Select…

A: Option D is correct .i.e FFF8H

Q: Find all the known condition code bits if a DEC instruction decrements that hexadecimal number 80.

A: Given hexadecimal number is 80 The binary representation of 80 is 10000000 DEC instruction…

Q: Create an entry for the execution cycle of the instruction "ADD E" using the Register Transfer…

A: example entry for the execution cycle of the instruction "ADD E" using Register Transfer Notation…

Q: Write an 8051 assembly code to display your name-surname on a 14 segment alphanumeric display,…

A: I Have answered this question in step 2.

Q: In the following instruction sequence, show the resulting value of AL in hexadecimal:…

A: The answer to the question is given below:

Q: ons of the benchmark is increased by 10% without affecting the CPI

A: given -   Find the increase in CPU time if the number of instructions of the benchmark is…

Q: Q3. Provide the hexadecimal representation of the following instruction.--- sd x17, 61 (x30) Ans:

A: A base-16 numeral system called hexadecimal representation uses 16 symbols to represent values: 0–9…

Q: Given the opcode of addu instruction as 0 and function code (funct) as Ox21, provide the instruction…

A: Solution:

Q: for the machine language instruction F70BD3  What is the Opcode in binary

A: Machine language instructions are the foundational building blocks of computer programs, serving as…

Q: Given the number Ox21100006, what is it when interpreted as a MIPS instruction? 1. The instruction…

A: MIPS instructions: The MIPS instructions can be represented in the binary format having a length of…

Q: Which segment will be accessed for the instruction MOV [BX],AH.

A: AX – This is the accumulator. It is of 16 bits and is again divided into two sub-8-bit registers AH…

Q: What is the reverse assembly of OxE8071020 machine language instruction? The Op-Code of the…

A: Given: What is the reverse assembly of 0xE8071020 machine language instruction? The Op-Code of the…

Q: Find the machine code for the instruction: SUB.B #15, W10 Machine code in HEX is: 0x v v What would…

A: Here SUB is mnemonic which stands for the subtraction of the contents of R from the accumulator.…

Q: Given the machine code, identify the instruction line or command line. Use CAPITAL LETTERS . No…

A: First convert the binary form to hexadecimal form. 0000111110110111 000101101010101100111111 to F B7…

Q: Determine the value after the instruction (signed division). AX = 0020H DL = FCH IDIV DL Select the…

A: Divides the signed dividend by using a signed divisor. Leftmost bit represents the sign (0 means…

Q: The instruction LH is a/an- R-format instruction I-format instruction J-format instruction Save O O

A: LH: It stands for Load Halfword. LH instruction has two operands. First operand is a general…

Q: Show the assembly instruction for the following machine code, given in hexadecimal. Explain all…

A: Solution for the above question is given in step 2:-

Q: A one-byte instruction has Oopcode and an operand O opcode only Oopcode and two operand Ooperand…

A: A one-byte instruction has opcode and an operand.

Q: Find out the instruction if machine code is given: 88 8D 00 10

A: Lets discuss the solution in the next steps

Q: Derive the machine code representation for the instruction blt r7, r8, LOOP for an Altera Nios II…

A: The answer is given below step.

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.